Electric Mobility Invacare Pronto M41 Electric Scooter Power Wheelchair - Answered Questions & Fixed issues
What does 3 blinking wrench lights mean?
It is indicating a left motor fault, which is not good news. This is usually from a motor overheating and burning out, usually from overloading the chair or from driving it on unstable terrain like mud, snow, wet grass or sand. If that is the case, there could be more damage to the electronics once you get the motor replaced too. Replacing the motor is a lot of work and very expensive, so you may want to try to find a replacement chair.
10/18/2022 4:31:18 PM •
Electric...
•
Answered
on Oct 18, 2022
•
2,077 views
A wrench light is on
When you turn the chair on and move the jostick the wrench light will flash you need to count the number of times it flashes to determine whats wrong ie 4 flashes pause 4 flashes pause. If its 4 flashes then you have a motor problem see my tips on flash codes to determine the problem. Whatever the problem is you will have to have the chair fixed by a tech or the provider that sold you your chair Hope this helps
10/18/2022 4:23:04 PM •
Electric...
•
Answered
on Oct 18, 2022
•
13,842 views
How wide is a pegasus4m-g
Standard interior doors are 28" while exterior doors are generally 36" wide. It is paramount to consider that a mobility scooter that is compatible with this size considering is most of the best mobility scooters are 27" wide, which makes for a tight fit unless you have plan it appropriately.
Width Between Arms 20" - 22.5"
7/26/2020 2:15:29 AM •
Electric...
•
Answered
on Jul 26, 2020
•
172 views
My pronto m41 was not
Hi I would invest in some new batteries ...if they have been in the chair for 3 years without charging them they r no good :::::: when batteries sit 4 a long period a coating forms on. The cells .when this happens they will never charge properly again ..cheers
3/3/2018 4:46:27 AM •
Electric...
•
Answered
on Mar 03, 2018
•
87 views
Joystick controller
Looks like the other experts are missing the point. The JS is locked out. I would take a pencil put some alum. Foil over the eraser and tap it in the button hole. Turn on the JS and tap the horn twice within 10 sec. This should reset the lockout. do not leave the pencil in the hole!
Strege Mobility I’m happy to assist further over the phone at
https://www.6ya.com/expert/bill_bcbb89783b08c489
6/16/2017 5:32:50 PM •
Electric...
•
Answered
on Jun 16, 2017
•
231 views
Rascal scooter 245
Most of these chairs have a clutch release lever near the motors. Move it into free-wheeling and it should roll nicely.
3/3/2017 9:56:17 PM •
Electric...
•
Answered
on Mar 03, 2017
•
318 views
Chair is slowing down. Batteries are fully
How old are the batteries? Even fully charged older batteries can be weaker and not give you as much power to keep the speed at what you are used to. Now a dragging bake can cause you to go slower and also drag the batteries down quicker. Try driving the chair and after awhile check each motor to see if they feel overly warm or hot If one or both feel very warm or hot then I would have the brake or brakes checked If they seen ok I would get the batteries replaced
9/18/2016 3:36:00 PM •
Electric...
•
Answered
on Sep 18, 2016
•
460 views
No power new batteries
Yes the control board is likely the cause if all battery connections are checked and pass
9/12/2018 9:28:14 AM •
Electric...
•
Answered
on Sep 12, 2018
•
356 views
No lights on joystick
Here is a parts catalog for the M41.
http://www.invacare.com/doc_files/06_108.pdf
If it was working fine before you swapped the batteries then you did something to interrupt the current flow. Pages 49/50 show the location of the controller with a picture. Unplug the connections here and make sure they are clean and in good shape. Make sure all other connections are clean and tight.
If you have 24V coming off the batteries into the controller, and 24V going out to the joystick from the controller and still nothing is working, then you will probably need to get ahold of an Invacare service tech to replace the joystick. Before he does that he should swap out the old joystick with a new one to see if that is the issue. Invacare parts are pretty pricey...joystick by itself is over $500.00. If the controller is shot, then you can double that cost. Sometimes, both need to be replaced as they can kill each other.
If the chair is old or has a lot of hard hours on it, you can usually shop around on Craigs List, etc and find a good newer/near new chair for about the same price as a new joystick replacement.
2/26/2015 10:35:48 AM •
Electric...
•
Answered
on Feb 26, 2015
•
226 views
Where is circuit breaker on pronto m 41
Hello,
The M41 does not have a circuit breaker, even if the owners manual says it does. There are fuses instead. One fuse on each battery. It is a very different looking fuse than one is use to seeing.
1/29/2015 12:27:58 AM •
Electric...
•
Answered
on Jan 29, 2015
•
927 views
How do I turn off the pronto m41 speed limiter
Hello,
The Pronto M41 does not have a speed limiter per say. If the chair used to go faster than it does now then you may have some kind of problem with the chair. If the chair has always driven' slow, that is slower than the maximum 3.5 to 4 MPH then a Invacare Remote programmer is needed to program the chair to go it's full speed.
Seek a Invacare dealer and ask them if they can check the programming.
1/29/2015 12:22:53 AM •
Electric...
•
Answered
on Jan 29, 2015
•
802 views
Not finding what you are looking for?