20 Most Recent Whirlpool Inglis IP8200 Dryer - Page 9 Questions & Answers

if the exhaust hose is clear of debris and you feel a good flow of air through it then ' Yes ' I would say that the heating element is bad.

c...

check the door switch,if this switch is bad dryer wont work,this is a spdt type switch as it runs the drum light when doors open and lets machine start and operate with door closed

One of the checks this unit performs when it starts is the drum belt, if the belt has slipped, broke or stretched, it wont start. You have to remove the top of the unit to see the drum.

Take it apart and put a thin bead of silicone on the glass and put it back together. The video might help. First though, you can just check that all those inner screws are tight. https://www.youtube.com/watch?v=FGSz5VFmkzs ..

Is there a position on the dial showing a symbol for a tub with a line above it? if it has position this against the mark and switch on then the pump will empty the sump into the water container and the machine can then be reset for normal operation

circuit board failure

where the voltage drops thats the issue check to switch then to power board then to control board

Make sure both pulleys the belt contacts are in alignment. Look for any metal parts close to the belt that may be shredding the belt.

no replace if failed bypass can damage unit and or cause fire /injury

FIRST YOU CHECK THE ELEMENT FOR RESISTANCE THE CHECK THERMAL CUT OFF TO MAKE SURE IT IS NOT OPEN IF YOU DO NOT KNOW HOW DO DO THE CHECK CALL A LOCAL REPAIR SRVICE

google Manual for whirlpool Cabrio Dryer WED6600VW0 for manuals

google whirlpool heat pump dryer error codes for more answers it is easy

Always first unplug the dryer from the wall outlet and then ohm test the thermal fuse, then disconnect the flame sensor and ohm test that, its located on the side of the burner tube. Remember no continuity going through it means it bad. Also, clean all the lent out of the dryer this should be done on a regular basis. I attached a website that has videos that will help you find the parts. I Hope this helps Tim https://www.appliancepartspros.com/repair-help/whirlpool-dryer-ggw9250pw3-repair/ggw9250pw3-no-heat-or-not-enough-heat.html

You can't work on gas appliances yourself. You need a Whirlpool gas certified technician. Fan working okay? May be a sensor thermostat?

E1=Thermistor open

post your email and i will send you the steps to fix and check it too much to type here

F04 indicates a fault in the heating circuit. It can be a main board, wiring, thermostat or heater fault. You would need to check the heater and thermostats with a multimeter to ensure they are not open circuit. . However, the first thing to try is a reset of the control board. . Turn the dial to off. Turn the dial clockwise to the 6 o'clock position. Press the start button 3 times Turn the dial 1 position clockwise. Press the start button 3 times. . This should erase the code. Try the machine again. If the code comes back, you need to check out the heating circuit. If you change or repair any part, reset the board, then try again.

You need a new run capacitor on the motor, or maybe a new motor itself. Due the cost, get a technician in.

If you disassemble the dryer, you probably will find the exhaust blower is clogged with lint (especially if you use softener). Also, the heating element(s) may have failed partially or a temperature sensor isn't working.

The recommended power cord is a 30 amp 3- or 4- wire cable. A 50 A cord could cause a problem by allowing a surge to the dryer motor and damage the dryer or start a fire. There are 30A to 50A adapters (see RV and boat supply vendors). The installation instructions for the LER5636EQ3 are available here: https://www.whirlpool.com/digitalassets/MLPDF/Installation%20Instructions%20-%203397618.pdf . See page 5 of the PDF. Note: the 50A outlet has a 50A circuit breaker protecting it. If you swap the outlet to a 30A outlet, you will also need to replace the breaker with a 30A one. I hope this helps. Cindy Wells

I'm wondering if the motor may have a problem & getting too hot it most likely has a breaker built into the motor that shuts it off if it gets too hot . If that's the case it should reset after a while when it cools . You might try running it then when it stops let it sit for a while & see if it will start again . If it starts let it run when it stops again feel the motor & see if it is real hot . Just something you could check . Hope this helps