20 Most Recent
Toymax Viore 42 in. Plasma TV - Page 3 Questions & Answers
Y Buffers or the Y
WE all hear that POP sound from time to time. I assume we are talking about a CRT, TV. That pop sound is most likely the OPT blowing.
Output Transistor, for the LOPT. Line out[put Transformer.
One of the two need replacing.
hope this helps.
Hello
Hello to you too, have a quetion, ask it
Viore 42" plasma tv has
The tv was working fine until this morning, then the picture went out but the sound is still working.
TV is only 3 years old, no real electrical problems
Cablevision remote won't work viore tv
I was able to program my viore tv by trying the code search:
1. Press the tv and sel buttons until the IO button turns red.
2. Press channel up or down until the tv turns off and the press the tv button to lock in the code.
Ps: Be pattient when searching for the code, it might take a while. HOPE THIS HELPS!!!!!!!!!!!!!!!!
Dish network code for a viore, volume/power not working
You can power scan for the code.
Turn ON the electronic device you want to program the remote to control.
Press the Mode button( sat,tv,dvd,aux) on the remote until the appropriate mode light is flashing.
Press the Power button. The mode light will stop flashing and stay lit.
Press the Up or Down arrow button to set the remote to the next code. The Down arrow button scans backward and the Up arrow button scans forward.
When the correct code is reached, the device (whether a TV, VCR, or other) will turn off.
Press the pound key button to store the code in the remote control memory. If the code is valid for your remote, the mode light will blink 3 times.
Turn the device back ON by pressing the Power button.
Press sat mode key once you power back on the tv to be able to operate the receiver box.
Try some other functions to make sure you have the correct code. Occasionally the Power button may work when others do not.
If the other buttons work you are finished.
.
If the other buttons do not work, repeat the previous steps. The scan will resume from the last code stored.
The mode light will flash rapidly when the scan has returned to the starting point and all codes have been tested for that mode. The remote control may not control some device models.
Herd a pop and think
It may not be the bulb. It could be a capacitor in the video circuit. If you look inside you will find a cylindrical object that has burst and has some wax around it. If you do, then replace this capacitor with exactly the same one.
My Viore clicks like its gonna come on then it
Hello,
Its the problem of overheating in the power supply board of the TV.on the power supply board of the TV there are few capacitors and IC.any of this IC is got short or may be weak.so due to this when you start the TV the current passes from electric outlet to the power supply board of TV.but when the current passes from that weak/faulty part at that time current gets stopped or slow and the board overheats and TV shuts off. this is a common problem faced by many other users too.the possible option to solve this issue is to check the power supply board by a meter and continuity tester and replace the faulty component on the board which is short due to which power supply board is getting overheated.its bit technical job but yes its not at all a costly repair to do or get it done by the technician. for required parts it can be easily available from local electronic hardware shop.]
This will help.
Viore pdp42v18ha tv went off
Hi,
Looks like, it is a thermal shutdown issue.
Try the following: Keep a fan and direct the air towards the bottom vent holes. Switch on the TV. Keep it on continuously for more than 2 hours and see if the TV shuts off again. If not, then it confirms Thermal shutdown..
ELse please give me the error blink code, ie What coloe does your LED blinks, and for how long it flashes..We can find the type of error directly from the blinking error code
Please leave it as comment, we may help you to solve your issue..
RNJ VINODKUMAR
Not finding what you are looking for?