Sanyo 42 in. LCD TV - Answered Questions & Fixed issues
No pic, just sound
Hi, you have not specified if your tv is still conventional tb that uses crt, or lcd
6/25/2017 2:33:00 PM •
Sanyo 42 in....
•
Answered
on Jun 25, 2017
•
112 views
I replace everything inside a sanyo dp42848. Power
Only for a little suggestion even when it has nothing to do with this to know ?
https://www.youtube.com/watch?v=t36YT7-5GTY but have you test those kind of fcc flatsheets by manipulating like for example pushing on it with a peace of towel on those sheets for a faultering test ? they can be dry out and come loose by direct sunlight or other cause by heating up over a time and it will become faultering.
Maybe it could be in cause of strange defects if you have service manual and all things measured do not use the new prints without heatsink it should allways on it if the same chipset is used if not modified , or you have bought a refurbished print because of the missing heatsink and metal cover?
6/5/2017 9:22:32 AM •
Sanyo 42 in....
•
Answered
on Jun 05, 2017
•
303 views
I have a Sanyo 42
I would just replace the TV, because any guess you make without the testing and equipment is just an expensive guess. New TV's are cheap by comparison. I have had a lot of TV'ds and the best do far is my Vizio 42 Inch LCD. 11 years old no issues.
5/20/2017 1:16:15 AM •
Sanyo 42 in....
•
Answered
on May 20, 2017
•
116 views
MY SANYO LCD TV MODEL 24 K 50 WAS OFF WHEN
Replace or have the powrer supply tested and eventually serviced.Lightning strikes affect two types of boards in televisions - the power supply by means of entering through the AC line and main boards by means of entering from the external signal sources. External antennas are worst and can totally toast the main board whereas a signal entering through HDMI cable from another device is less likely to be affected by a power surge.So naturally you start your quest with the power board , which is the usual suspect.As of right now I do not believe we have an announced service for the power supply board of Sanyo LCD-24K50, but if you do not have any other options you can always try and send the power board for examination/repair through
http://www.coppelltvrepair.com/newservice.Good luck!
12/27/2016 6:28:45 AM •
Sanyo 42 in....
•
Answered
on Dec 27, 2016
•
232 views
Does anyone know the remote code for a sanyo tv model dp42647 on a dishnetwork remote
https://www.
mydish.com/support/
remotecodes
Remote Control Manuals · Program Remote to TV/Other .... remote, product type, and manufacturer below to see the current known remote codes you should try.
https://www.directly.com/.../
dish-network-my-dish-
remote-needs-
progra...
My Dish remote needs programming for Sanyo TV, Model DP226649. My Dish ... Needcode. Alta asked this ... Dish Network • 16808 answers • 95% helpful. Code is ... Test volume control, if it works you're set ... try 590 it should work. tivosat.
https://www.directly.com/.../
dish-network-how-do-i-
program-my-dish-
re...
Dish Network. How do I program my dish remote to work for my Sanyo TV. ... entercode 590 press pound then sat Then try to turn tv on and off then try volume.
7/22/2016 12:20:58 AM •
Sanyo 42 in....
•
Answered
on Jul 22, 2016
•
2,534 views
Total Control Universal Remote. URC 4140. What is the 4 digit code to operate the above TV
Search Results
www.remotecodelist.com/remotes/URC_4140_B00_and_B01.pdf
UNIVERSAL. Remote control. URC - 4140 ... Your TOTAL CONTROL can operate four devices: a Television, ... The TV, VCR/DVD, SAT and AUX keys select the device.... 4. Enter your four-digit code using the number keys. The red light will blink twice.... To set up your other devices, follow the same instructions above, only.
www.remotecodelist.com/
Codes and links for a number of universal remote controls, including Sony, RCA, ... GE Remote Codes, General instructions for GE Universal 3 and 4 digit remote controls. ... This manual may work for a number of Philips-Magnavox remotes. ... Total Control URC-4140, PDF Instruction Manual (remote also known as Crest .
8/25/2016 5:40:50 PM •
Sanyo 42 in....
•
Answered
on Aug 25, 2016
•
1,042 views
Fix a sanyo lcd tv model 42840 will not power up (?)
Fault at its main digital board.
Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electronicshelponline.blogspot.com/
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.
6/14/2016 9:21:19 AM •
Sanyo 42 in....
•
Answered
on Jun 14, 2016
•
110 views
Tv shows one half picture . The other half is black .
Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electro-medical.blogspot.com/
http://electronicshelponline.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced.
12/27/2015 12:12:15 PM •
Sanyo 42 in....
•
Answered
on Dec 27, 2015
•
78 views
My Sanyo Television model#DP26640-07 has sound &a blank screen ?
Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electronicshelponline.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement.
11/12/2015 11:56:44 AM •
Sanyo 42 in....
•
Answered
on Nov 12, 2015
•
106 views
The new universal will adjust the volume but will not let you access channel number 3 or 4, or, any number.
You have to check other set-up codes said for your TV brand with this remote control. Check them. Then choose one code, that will give you maximum functionality with the set. This is the only way, and is true for any universal remote controls. It is a trial and error method. But, if the remote control is its original one, this probem will not be there. Be patient, and try some codes said for your TV brand. Be patient. No other way.
Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily.
http://remotesearch.blogspot.com/
http://electronicshelponline.blogspot.com/
http://electrohelponline.blogspot.com/
Search the site by type in the brand name of your device, in the "Search box at the top right of the Home page display" to see the set-up codes to your device, with different brand remote controls.
10/22/2015 12:59:48 PM •
Sanyo 42 in....
•
Answered
on Oct 22, 2015
•
49 views
Why won't it turn on?
Fault to its main board.
Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electronicshelponline.blogspot.com/ . In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
10/7/2015 12:34:29 PM •
Sanyo 42 in....
•
Answered
on Oct 07, 2015
•
108 views
Cost for a cracked screen
Not cost effective for a set that size- cheaper to replace with new set and also have a warranty.
10/6/2015 5:50:22 PM •
Sanyo 42 in....
•
Answered
on Oct 06, 2015
•
54 views
Not finding what you are looking for?