20 Most Recent GE Profile Spectra JGBP79 Gas Kitchen Range Questions & Answers


take a look at the igniter located in the center of two burners. clean the gap with a stiff brush between the eletrode and the upper plate. the distance is preset at the factory. you may have enough buildup to close the gap enough to trigger the igniter.

GE Profile... | Answered on Dec 19, 2017


You are correct, it's the heat sensor. Easy to replace.

GE Profile... | Answered on Dec 02, 2017

GE Profile... | Posted on May 21, 2017 | Be the first to answer


its making a circuit, just see which way the spark is jumping then you will know if it is going the right way, like a light bulb it will work either way

GE Profile... | Answered on Apr 26, 2017

GE Profile... | Posted on Mar 28, 2017 | Be the first to answer


No oven ignition is usually thermostat issue.

GE Profile... | Answered on Nov 25, 2014

GE Profile... | Posted on Jun 21, 2014 | Be the first to answer


The self clean option usually can't be stopped once its started. you may have to let it finish its cycle (a few hours) and see what happens from there. It also sounds like you could have a bad door sensor switch.

GE Profile... | Answered on Apr 01, 2014

GE Profile... | Posted on Dec 30, 2013 | Be the first to answer

GE Profile... | Posted on Nov 26, 2013 | Be the first to answer

GE Profile... | Posted on Sep 28, 2013 | Be the first to answer

pdf Manual

Profile Spectra JGBP79 Gas Kitchen Range Manual

GE Kitchen Ranges | Uploaded on Sep 23, 2013


Hello,
The F1 error code means that the computer thinks a button on the touchpad is stuck. Sometimes this can be resolved by making sure the touchpad connector fits tight into the control board. The F1 code can be cleared by pushing CANCEL/OFF. If it returns the touchpad needs to be replaced GENE

GE Profile... | Answered on Mar 20, 2013


For women from a woman's point of view: Most if not all the screws were hex head 1/4. Have appropriate tools. A socket set will work. I like my little cordless screw driver. You will also need wire strippers and two wire nuts, they say ceramic wire nuts and electrical tape. It is also a good idea to have a someone else there for safety sake. I tipped the stove back.
Take everything our of the oven. Take big screws out at the back bottom of oven. Lift bottom of oven and push toward the back of oven. (There is a lip at the front that oven floor slides unde). Be careful as there are sharp edges all over the place once this oven bottom is off. Next unscrew the screw at the front middle of oven that holds the long burner in place. Next pull the stove drawer out and set aside. Pull stove out just enought to put large juice cans under the front legs. Way at the back you will see where the burner comes down to the gas line. There are two screws holding it to the back of the stove, remove them. Next find the two wires that come from the igniter. Unplug them. Lift out the burner. Unscrew the two screws that hold the igniter on to the burner. Carefully put the new ignitor on the burner. If the new ends do not match the old ones or if they are shorter, cut the old ones off near the old ignitor. Cut the ends off the new ignitor as far from the ignitor as you can. Clean the ends off so that about a half inch of wire is bare. Put the old ends on the new wire so that you can plug them in. Hold the two like wires so that both bare wires are parallel and screw on the wire nut. Lay it parallel to one wire and wrap electrical tape around it so that it will not pull loose. Plug in the way it was originally. Put everything back together opposite of the way you took it apart.

GE Profile... | Answered on Feb 23, 2013

GE Profile... | Posted on Oct 27, 2012 | Be the first to answer

GE Profile... | Posted on Oct 16, 2012 | Be the first to answer

GE Profile... | Posted on May 21, 2012 | Be the first to answer

GE Profile... | Posted on Mar 24, 2012 | Be the first to answer


Anyone has any information as to how to fix my describe problem with GE Profile Gas Range I have.

Thanks

GE Profile... | Answered on Nov 20, 2011


Hi,

The ignitor is not working right and is going bad....
have the repair man replace the ignitor, or DIY....
Check out this tip about your problem...

Oven not Working or Oven not Heating

Oven Problems Replacing the Igniter

heatman101

GE Profile... | Answered on Feb 10, 2011

Not finding what you are looking for?
GE Profile Spectra JGBP79 Gas Kitchen Range Logo

100 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

GE Profile Spectra JGBP90 Gas Kitchen Range
GE Profile Spectra JGBP90 Gas Kitchen Range

1,136 Questions

GE Spectra JBP78 Electric Kitchen Range
GE Spectra JBP78 Electric Kitchen Range

375 Questions

GE Spectra JGBP35 Gas Kitchen Range
GE Spectra JGBP35 Gas Kitchen Range

101 Questions

GE Profile JGS968 Gas Kitchen Range
GE Profile JGS968 Gas Kitchen Range

81 Questions

GE JGBP28 Gas Kitchen Range
GE JGBP28 Gas Kitchen Range

67 Questions

Top Kitchen Ranges Experts

Ismael Rodriguez...

Level 2 Expert

184 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. Profile Spectra JGBP79 Gas Kitchen...

Profile Spectra...

View Most Popular

GE Kitchen Ranges

  • GE Kitchen Ranges

Most Popular Question

installing wb2x9154

  • Kitchen Ranges
Loading...