Ricoh Aficio 1232C Color Copier - Answered Questions & Fixed issues


Download Twain Driver from ricoh site and you can use any softwere that suports twain scaning i use microsoft scan that comes with office 2003

Ricoh Aficio... | Answered on Apr 18, 2018 | 1,248 views


You have to go into service mode.

Ricoh Aficio... | Answered on Nov 26, 2014 | 54 views


there may b ur optics dirty
or the cleaning blade faulty to clarify the problem just take out a print of counter if line occurs then ur cleaning blade faulty if counter is clear then claen the optics or scanner mirrors

Ricoh Aficio... | Answered on Sep 24, 2014 | 71 views


you need to adjust the lead edge trim
press yellow C and 107 and press and hold red C button
then go to copy SP
select 2 drum
then look for trim adjust
and then select front
then change values up and down until you get the correct registration. you can do a test copy while on SP mode by pressing copy window.

Ricoh Aficio... | Answered on Sep 30, 2014 | 84 views


SC822 is a hard drive error. that machine has 2 installed and should be replaced as a pair. it's hard to determin which one has failed.

Ricoh Aficio... | Answered on Jul 09, 2014 | 56 views


need to clean the optics for sc-172

Ricoh Aficio... | Answered on Apr 23, 2014 | 55 views


check your copier sensors that read toner density in your aficio 1232C

Ricoh Aficio... | Answered on Apr 14, 2014 | 29 views


check da chip on da toinner

Ricoh Aficio... | Answered on Apr 06, 2014 | 17 views


SC 792 :Finisher error .The machine does not recognize the finisher , but recognizes the relay unit .Possible causes :Defective connectordefective cable incorrect installation

Ricoh Aficio... | Answered on Apr 09, 2014 | 998 views


CHECK ALL THE SENSOR WHERE THE PAPER PATH GOING TO EXIT

Ricoh Aficio... | Answered on Feb 10, 2014 | 275 views


Have you just bought this 2nd hand? if its flashing in the bottom left corner? can you still print to it?

Ricoh Aficio... | Answered on Sep 19, 2014 | 60 views


replace the ram in the hard disk board will solve the porblem

Ricoh Aficio... | Answered on Aug 10, 2013 | 55 views


Usually the setting of yout network with your copier/printer setting is mismatched so your printer.copier did not understand. What you can do you should check the system setting of your copier/printer and print it out then you should find the driver of your printer/copier in the add printer hardware secrtion in control panel of your computer network . Before you reinstall it , you should uninstall the previous driver so there is no conflict when you reinstall new driver . Try it

Ricoh Aficio... | Answered on Jun 19, 2013 | 4,315 views


The scan mode is optional.

Ricoh Aficio... | Answered on Feb 07, 2013 | 50 views


The wastw toner box is located under drum unit.2_7_2013_5_55_42_pm.jpg

Ricoh Aficio... | Answered on Feb 07, 2013 | 48 views


To enter service mode press the following : yellow "Clear" then press the numbers 1 then 0 then 7 then press and hold the red "Stop Clear" button until the display changes..... Good Luck

Ricoh Aficio... | Answered on Sep 27, 2012 | 46 views


The correct way to get into service mode is to first press the Yellow "CLEAR" button then press the numbers 1 >0>7 then press and hold the Red "STOP" button.... Good Luck

Ricoh Aficio... | Answered on Jun 10, 2012 | 521 views


We are assuming that you are talking about Error Code SC 221
This code is a Scan length detection problem.
1.Disconnected Sychronization Detector
2.Bad LD-Unit/BICU Board

SOLUTION: Replace the Laser Diode & Laser Sync detect board

Hope helps (remember to rating this free answer).

Ricoh Aficio... | Answered on Mar 27, 2015 | 421 views


SC122
[Cause]
SDRB board is faulty.
[Resolution]
Replace the SCRB board and ground.

AND
SC122 occurs while scanning.
Does not occur when scanning at the same magnification; occurs when copying and enlarging.

[Cause]
Scanner motor is faulty.
[Resolution]
Replace scanner motor.

And one thing to check is to make sure the set screw that locks the cable pulley to the scanner drive shaft didn't back out or shear off.

Ricoh Aficio... | Answered on Sep 23, 2011 | 74 views


lets start with whats the trouble of your machine? are there SC codes that appear on your machine? so we could help or inform you if you need a technician or you can repair it by your self.

Ricoh Aficio... | Answered on Sep 09, 2011 | 43 views

Not finding what you are looking for?
Ricoh Aficio 1232C Color Copier Logo

Popular Tags

112 questions posted

Ask a Question

Usually answered in minutes!

Top Ricoh Office Equipment & Supplies Experts

Adorjani Laszlo

Level 3 Expert

1316 Answers

quennie732

Level 2 Expert

422 Answers

Bernard D'Souza

Level 2 Expert

163 Answers

Are you a Ricoh Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...