20 Most Recent GE WHRE5260E Top Load Washer - Page 5 Questions & Answers


You are right. Sounds like the washer is not being told to shut off. If the washer will stop filling when the power is shut off to it: Open the front panel by using a putty knife to push in on the clips about two inches in from each side at the seam of the front panel and the washer top. Tilt washer front panel forward and lift off bottom pegs. Pull the tube off the outer tub at the left side, cut off and inch and a half, poke a thin wire into the hole on the tub end and remove, then put the tube back on. (do this with the tub empty) You can only do this one or two times before the tube starts to get too short, so from now on, every two or three months, fill the machine to the lowest water level with hot water and several cups of bleach and run a cycle, including rinses, to help prevent the goop from reforming in the tube area again.
If machine still fills when power is off, replace water valve.

GE WHRE5260E Top... | Answered on Nov 12, 2008


It sounds like it could be the lid switch, check to make sure the lid switch is clicking when you close the lid.

GE WHRE5260E Top... | Answered on Nov 01, 2008


I will tell you for 14.95. Thanks for the info anyway. Send no more emails.

GE WHRE5260E Top... | Answered on Oct 15, 2008


If when the machine is flooding if you turn off power to the machine and it continues to fill: replace water inlet valve. If flooding water stops filling when power is interupted: clean out the end of the water level switch tube where it connects to the outer wash tub.

GE WHRE5260E Top... | Answered on Sep 29, 2008


hi If the washer won't fill or fills very slowly, if it overfills, or if the water is the wrong temperature, the water inlet valves could be faulty. These components are easy to locate and very easy to replace, at little cost. When you suspect an inlet valve is faulty, first check to make sure the water faucets are fully turned on and properly connected to the hot and cold inlets of the valves. Then check the screens in the valves; if they're clogged, clean or replace them. If water doesn't enter the tub, set the temperature control to the HOT setting. If there is no water, set the control to the WARM setting. If all that comes out is cold water, the hot-water inlet valve is faulty. Reverse the procedure to test the cold-water valve, setting the control first on COLD and then on WARM. If the tub overfills, unplug the washer. If water still flows into the tub, the valve is stuck open. In any of these cases, the valves should probably be replaced. To check the valve assembly:

Step 1: Remove the back service panel and disconnect the hot-water and cold-water hoses to the valves.
Step 2: Remove the hoses connected to the valves inside the cabinet. Also disconnect the wires from the terminals. Back out the screws holding the valves to the machine. The inlet valves have solenoids (a coil of wire that carries a current) inside the housing. These can be tested, but chances are the valves are simply worn out.
Step 3: Tap the solenoids with a screwdriver handle. If this doesn't work, replace the entire inlet valve assembly. Repairs usually cost more than a new part. Make sure the replacement valve assembly is exactly the same type as the old one. Install it in reverse order of the way you disconnected the old one.

GE WHRE5260E Top... | Answered on Sep 13, 2008


Hi thanks for the question ,YEs i can tell you how to remove the clutch Remove front panel .Motor is held in place wiyh 4 3/8 nuts underneath the motor remove the motor .The clutch is held in place with a spring clip at the end of motor . Remove clip Now the clutch should come off thanks for the question

GE WHRE5260E Top... | Answered on Sep 12, 2008


hI THANKS FOR THE QUESTION dOES THE MOTOR SORT OF STOP & START ON THE SPIN CYCLE .iF IT DOES DO THAT .yOU NEED A CLUTCH LOCATED UNDER NEATH TEMOTOR AT MOTOR SHAFT tHANKS FOR THE QUESTION tHE APPLIANCS DOC

GE WHRE5260E Top... | Answered on Sep 12, 2008


HI THANKS FOR THE QUESTION . tHE PROBLEM WITH YOUR WASHER IS THAT YOU NEED A NEW WATER VALVE .tHANKS FORTHE QUESTION tHE APPLIANCE DOC

GE WHRE5260E Top... | Answered on Sep 12, 2008


Hi thanks for the question On a ge dishwasher , more often than none it leaks from the motor seals If thats what the problem is you will see it leaking from the motor shaft , It could be leaking from above the motor if it si from the tub ,Replace the part that joins the motor to the tub if its motor seals .Replace motor seals

GE WHRE5260E Top... | Answered on Sep 12, 2008


Hi thanks for your question . Yhe only reason you would want to take the agitator off would be to remove the tub .And thats tye only reason thanks for the question The appliancd doc

GE WHRE5260E Top... | Answered on Sep 12, 2008


Thanks for the question On a ge washer If you over load or the washer did not drain fast enough or over suds ing , when the washer starts to spin the forse of the spin will push water up the pressure switch hose causing the washer to start & stop spinning Thanks for the question THe appliance doc

GE WHRE5260E Top... | Answered on Sep 11, 2008


Thanks for the questionOn a ge washer theres a over flow tube located at the back left side Sometimes if you use a high sudzing detergent , it could leak not to much to worry about just change detergent to a low sudzing one THanks for the question The appliance doc

GE WHRE5260E Top... | Answered on Sep 11, 2008


HI thanks for your questionOn your washer theres a electric pump sometimes foreign objects get caught in pump remove front panel . Using a blade screwdriver insert between top & front panel about 2 inches from corner .The front should now come off .The pump is on the left side . Disconnect pomer If your washer is full of water now put drain hose on floor or in bucket to drain water . Now remove hoses from pump & clean reinstal . Thanks for your question The appliance doc

GE WHRE5260E Top... | Answered on Sep 11, 2008


sounds like blocked pump or hole in the discharge pipe

GE WHRE5260E Top... | Answered on Aug 27, 2008


it sounds like the basket is not locked when it is agitating, if so the water will climb the wall during the wash cycle and leak out of the overflow (which is the plastic tube you described). if this is the case, it is a transmission brake problem. it can be fixed by a professional, but you might want to look into buying a new machine.

GE WHRE5260E Top... | Answered on Jul 30, 2008


take a butter knife and release the two clips on the top of the front panel (look in the seem between the top and front panel and push the butter knife directly into the clips), this will release the front panel from the machine. then you can see where the water is coming from.

GE WHRE5260E Top... | Answered on Jun 27, 2008


it sounds like the bleach fill line. at the top of the washer is a bleach fill cup, it might attach to it. this black bleach fill line attaches to the bleach fill cup to the bottom of the tub.

GE WHRE5260E Top... | Answered on Jun 27, 2008


if you are only getting hot water on warm setting possible bad inlet valve cold side ck wiring first just to be sure wire to cold side not loose

GE WHRE5260E Top... | Answered on Jun 08, 2008

Not finding what you are looking for?
GE WHRE5260E Top Load Washer Logo

150 questions posted

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

geapptech

Level 2 Expert

157 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Washing Machines

  • GE Washing Machines

Most Popular Question

washing machine water level sensor not

  • Washing Machines
Loading...