20 Most Recent GE WHRE5260E Top Load Washer - Page 6 Questions & Answers


Wet clothes should not be left in the washer over night as mold will develop and cause a moldy odor. You could run the load through a rinse cycle with fabric softener or baking soda to get rid of the odors.

GE WHRE5260E Top... | Answered on Jun 07, 2008


there is a tub seal under the spin tub that proab needs replacing open the front panel then raise the top then grab the agitator and **** up on it hard it should snap out then unsnap the splash ring around the outer tub take the little bolt out of the agitator drive loosen the nut on the spin tub and remove it keep going down till you get to the tub seal replace it then reassemble

GE WHRE5260E Top... | Answered on May 22, 2008


THAT COULD BE A BROKEN or LOOSE SCREW THAT HOLDS THE INNER TUB in the Center mast, hope this helps AJ

GE WHRE5260E Top... | Answered on May 09, 2008


it should be in your use and care guide

GE WHRE5260E Top... | Answered on Mar 27, 2008


The mixing valve needs to be replaced. It should be under $50 and is easy to do.

GE WHRE5260E Top... | Answered on Jan 23, 2008


THE COUPLIN BETWEEN THE MOTOR AND THE TRANSMISSION IS BROKE!  IT'S EASY TO FIX.

GE WHRE5260E Top... | Answered on Oct 11, 2007


Maybe that a sock or other piece of clothing get between the clothes tub and the outer tub and holds the drum. Check the outer tub port- open the washer's main access panel and remove the large diameter rubber hose that connects the pump to the bottom of the outer tub. Then,try to remove the clothing through the port. Good luck !

GE WHRE5260E Top... | Answered on Aug 31, 2007


I am thinking there may be an object caught between the inner and outer tubs...perhaps something came out of a pants pocket and was "flung" overboard into the outer tub. If you remove the top, and push the inner tub (moving tub) to one side, look with a flashlight for a foreign object. the noise will be fine until high speed kicks in and begins to disturb the sleeping object into a frenzy.

GE WHRE5260E Top... | Answered on Aug 22, 2007


sounds like the timer needs a little assistance to get "over the hump". perhaps many cam switches must be switched at his point of cam rotation. if machine is getting old, then attempt to lubricate the electric motor that turns the timer mechanism. also lube the shaft bushings for the timer cam plate as well if possible.

GE WHRE5260E Top... | Answered on Aug 18, 2007


First locate were the sound is coming from. put your ear very close to the timer and listen for this clicking sound. remember a timer will make a clicking noise which makes the timer go around. Timers can get noisey with age. The sound might be coming from below also .I would run your washing machine until the part fails. They might also have a motor controller in this unit which is seperate to the timer which will make a high pitch clicking noise.

GE WHRE5260E Top... | Answered on Aug 18, 2007


Sounds like you have a bad fill valve on the cold water side. If your hoses are not clogged, then remove the hose and check the cold water inlet going into the machine for clogs. There is a screen that can trap mineral deposits and/or rust. If you have well water or hard water, they can become clogged easily. Sometimes you can clean them out and they will work just fine. Most of the time, however, you will need to replace the fill valve. Make sure you unplug the machine and turn the water off. The valves are electronically controlled. I hope this helps.

GE WHRE5260E Top... | Answered on Aug 17, 2007


It could be any number of things stopping it running. Call a GE Service technician to diagnose and fix.

GE Washing... | Answered on Jan 11, 2020


I have just received my 3rd paycheck which said that $16285 that i have made just in one month by working online over my laptop. This job is amazing and its regular earnings are much better than my regular office job. Join this job now and start making money online easily by just use this link......HER? www.bayusd11.com

GE Washing... | Answered on Jan 11, 2020


If the Fill light is flashing or H2O SUPPLY is scrolling on the display (2015 and newer models): the washer will initiate a 3 or 4 minute lock-out period (depending on model). The washer controls won't respond or change during this time. After 3 or 4 minutes, you can choose your settings and press Start. Unplugging the washer will start the 3 or 4 minute lock-out period again.

GE Washing... | Answered on Jan 09, 2020


Hi,
There should be a chrome label on the back of the machine, some times on the sides.

Thx

GE Washing... | Answered on Nov 22, 2019

Not finding what you are looking for?
GE WHRE5260E Top Load Washer Logo

150 questions posted

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

geapptech

Level 2 Expert

157 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Washing Machines

  • GE Washing Machines

Most Popular Question

washing machine water level sensor not

  • Washing Machines
Loading...