Top 20
GE WHRE5260E Top Load Washer Questions & Answers
Where can I find a diagram of a ge whre5260e? I'd like to find the agitator.
When the machine agitates, it stops working. The belt has a lot of tension at this point.
stops working?? does it trip shutdown what
your info is far too sparse to make any definitive view
if the belt and rotors gears {egg gear} has failed
you would hear it grinding
so can you hear the motor running
ie youll hear the water circulation motor pump
usually one motor is used for both
if this is the case and the motor runs then its the gear system thats wrong
check the agitator motor start up capacitor hasnt failed
the info you give isnt good enough
Washing machine water level sensor not working
You can do one or 2 things. Drain the machine, disconnect the pressure tube going to the level switch and reconnect it. Check the actual switch itself and make sure it is working and also check that it hasnt fallen off and shorted itself against the frame of the washing machine. I see these switches fall off inside a lot.
GE WHRE5260EWW washer sounds like a jet when it spins
On a modern washer there will be an Engineers Program which is invoked by a key combination press. You can control all the functions from there and do tests. 1200 rpm is the Ideal speed for a washing machine for good reasons... Ask any Woman this !!Google your Model with Engineer Program etc.We have a range of Service Manuals at: www.spotless-service.com and adding many new ones everyday.
HOW MUCH WATER A WASHER
Hi from retired Englishman in SW France,
I'm sorry but you are not actually talking to any particular manufacturer but a FixYa forum and the forum is just made up of ordinary guys and gals, probably at home and from all over the world, with experience of addressing problems and giving guidance for free on the web. Also members on Fixya are not 'affiliated' to, or representative of, any manufacturer at all, just using their experience gained probably over many years.
So-
Have a look at the manufacturer's panel, probably on the back- it might give you an indication there- or your manual?
Another possibility would be to go onto the manufacturer's web site DIRECT to see, OR your (intended) vendor's site?
If this has assisted and/or clarified the situation for you please consider a 4 thumbs up on our rating.
Thanks and good luck!
John C
How do you test a ge washer motor
Use an ohmmeter across all the windings, they should be a few ohms (my washer is 2.3 to 2.7 ohms). There is probably a service manual inside the front, bottom panel that will give you the exact range for your motor and that also gives you the pin definition of the connector so you know what pins the different windings attach to.
I have a GE washer model # whre5260e1ww the washer
Greetings,
I've worked on many of these machines and since I can't physically speak to you about problems...I'll do the next best thing and tell you what it might be...
#1 if the motor is going bad, it will overheat and cut off and stay off 10 minutes to maybe 3/4 of an hour and then come back on..
#2 the main board can be going bad and stops by itself
There really isn't that much on this model to cause your problem...I pray this helps you,Bruce Denton
Is it possible to slow down or reduce the rate at
There is no flow adjustment on the drain on any washing machine, I had a similar problem on my old washing machine, I discovered the problem was the waste water pipe in my house was clogged with scum from detergent residue, I poured liquid plumber where the washing machine drain hose goes into the waste pipe in the house waited for 1/2 hour, then filled the washing machine with hot water, reinserted the drain hose, and wrapped it up with duct tape to prevent further leaks, and the force of hot water uncloged the pipe, .Problem solved
The drum on my G.E.
Hi, did you say the drum of the washer hangs down from the top panel?
If that be the case, you certainly have to replace the shock absorber to make the drum balance again.
Not finding what you are looking for?