GE WHRE5260E Top Load Washer - Page 4 - Answered Questions & Fixed issues
No Power
hI THANKS FOR THE QUESTION dOES THE MOTOR SORT OF STOP & START ON THE SPIN CYCLE .iF IT DOES DO THAT .yOU NEED A CLUTCH LOCATED UNDER NEATH TEMOTOR AT MOTOR SHAFT tHANKS FOR THE QUESTION tHE APPLIANCS DOC
Caloric Dishwasher DUS203190A
Hi thanks for the question On a ge dishwasher , more often than none it leaks from the motor seals If thats what the problem is you will see it leaking from the motor shaft , It could be leaking from above the motor if it si from the tub ,Replace the part that joins the motor to the tub if its motor seals .Replace motor seals
Can the clutch on a ge s4200B1WW be replaced
Hi thanks for the question ,YEs i can tell you how to remove the clutch Remove front panel .Motor is held in place wiyh 4 3/8 nuts underneath the motor remove the motor .The clutch is held in place with a spring clip at the end of motor . Remove clip Now the clutch should come off thanks for the question
Agitator on washing machine
Hi thanks for your question . Yhe only reason you would want to take the agitator off would be to remove the tub .And thats tye only reason thanks for the question The appliancd doc
GE wpse4200aoww washer won't stay in spin mode
Thanks for the question On a ge washer If you over load or the washer did not drain fast enough or over suds ing , when the washer starts to spin the forse of the spin will push water up the pressure switch hose causing the washer to start & stop spinning Thanks for the question THe appliance doc
GE profile washer
Thanks for the questionOn a ge washer theres a over flow tube located at the back left side Sometimes if you use a high sudzing detergent , it could leak not to much to worry about just change detergent to a low sudzing one THanks for the question The appliance doc
Washing machine won''t drain
HI thanks for your questionOn your washer theres a electric pump sometimes foreign objects get caught in pump remove front panel . Using a blade screwdriver insert between top & front panel about 2 inches from corner .The front should now come off .The pump is on the left side . Disconnect pomer If your washer is full of water now put drain hose on floor or in bucket to drain water . Now remove hoses from pump & clean reinstal . Thanks for your question The appliance doc
Water leaking
sounds like blocked pump or hole in the discharge pipe
Overflowing
This is a symptom of a pressure switch problem. Open the console and double check the pressure switch (located behind the water level knob) and make sure the rubber hose is still attached. In many case, this hose vibrates loose and comes off the pressure switch. Without the hose attached, the pressure switch never senses the change in pressure from the wash tub required for it to be shut off. The end result: your washer continually fills without shutting off. If it is a simple hose problem, you can prevent this from reoccurring by placing a small zip tie around the air hose at the point where it attaches to the pressure switch. Do not over-tighten as you may damage the switch fitting. Just make it snug.
If the air hose is still attached, and the electrical connections are still attached, replace the pressure switch. I could not find a part number with the model number you listed this under. Please double check you model number again and post back, so I can assist you finding the correct part (if needed). I hope this helps you. Let me know if you have further questions.
Fixn my GE washer spin cycle
It sounds like it could be the lid switch, check to make sure the lid switch is clicking when you close the lid.
Leaking from the front
take a butter knife and release the two clips on the top of the front panel (look in the seem between the top and front panel and push the butter knife directly into the clips), this will release the front panel from the machine. then you can see where the water is coming from.
GE Top-loader Leaks Water from Vertical Tube Behind Tub on X-Large Loads
it sounds like the basket is not locked when it is agitating, if so the water will climb the wall during the wash cycle and leak out of the overflow (which is the plastic tube you described). if this is the case, it is a transmission brake problem. it can be fixed by a professional, but you might want to look into buying a new machine.
Water leak
it sounds like the bleach fill line. at the top of the washer is a bleach fill cup, it might attach to it. this black bleach fill line attaches to the bleach fill cup to the bottom of the tub.
Water leaking
water leaking from under the machine while running. Also will not stop filling in the rinse cycle.
GE washer
if you are only getting hot water on warm setting possible bad inlet valve cold side ck wiring first just to be sure wire to cold side not loose
Water leaking where motor goes into the drum
there is a tub seal under the spin tub that proab needs replacing open the front panel then raise the top then grab the agitator and **** up on it hard it should snap out then unsnap the splash ring around the outer tub take the little bolt out of the agitator drive loosen the nut on the spin tub and remove it keep going down till you get to the tub seal replace it then reassemble
Not finding what you are looking for?