GE WHRE5260E Top Load Washer - Page 8 - Answered Questions & Fixed issues

Hello Sounds like your likely problem would be the Display Board or User Interface Board part # WH12x10544 , Hope this helps .

This suggests a communication issue. https://www.fixya.com/support/t29731810-ge_fridge_displays_0000 Call a local GE refrigeration engineer. There is a video if you want to try some things. https://www.google.com/search?q=Ge+model+pfss5rkzhss+is+flashing+0+on+the+control+panel ..

Although you posted that a few years ago, I'll still give my 25¢ From top left to right: red pin, blank blank Middle left to right: black, white, blue Bottom left to right: orange, yellow, purple Top left pin (red) is positive and 1st left pin in middle (black) is negative. Straight 120v, but I don't know how to vary the speed by utilizing the other pins

I would check the drum bearing and mounting.

https://f01.justanswer.com/smitty1486/f1e3636b-6c6d-4de9-b0e7-bcf462c895de_ScreenHunter_5249_Dec._09_08.50.jpg https://www.justanswer.com/appliance/auy5a-ge-profile-range-it-s-showing-f50-code-whats.html

Yes, you can try a power cycle on it, but you probably need a service call. Likely a control board issue.

You need to replace the machine. Most parts are no longer available and the part that is likely to be faulty is not even listed on the schematic! The type of machine has a mechanical timer. If you can get into the top unit, you could try spraying some WD40 into any gaps you can see in the lump at the back of the main control knob. There is a small synchronous motor that drives it. https://products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-90150.pdf Top parts schematic. Click + to enlarge http://assets.geappliances.io/parts/00000000/00018400/00018470.p01_2325.jpg Non availability of parts! https://www.geapplianceparts.com/store/parts/ModelSectionParts/WBSE3120B2WW/1/0/0/0/CONTROLS_&_BACKSPLASH Front Loaders hold just as many clothes, wash better, and use a fraction of the water and electricity using HE Detergent.. ..

It is a job for the Service Techs, they have the special tools needed. videos https://www.google.com/search?q=ge+model+wjre5550h+replace+agitator+dogs ..

Claim on the guarantee as it has happened within the warranty. You need a new Water Inlet Valve. The solenoid isn't closing shut. The other possibility is that your home water pressure is too high. A plumber can test that and fit a pressure reduction diaphragm. https://www.google.com/search?q=ge+spacemaker+model+gud27essmww+water+inlet+valve ..

possible leak in soap dispenser or tube coming from it

Humming is normally caused by a failed start capacitor. Smoke would normally be the motor or wiring, but I am a little puzzled by the smoke inside the machine, and can only think there is a gap on the top of the drum to the top panel. In all likelihood, you need a new motor, but due to the cost of them, I would suggest getting a service tech in. Or you could remove the motor and take it to a local electric motor sales and repair outlet and ask if they can test the capacitor and motor. https://www.google.com/search?q=electric+motor+repair ..

Could be Drive coupling, Clutch dogs or Gearbox. Arrange a service call. They are all messy jobs and need a lot of stripping down and in some cases a special tool. There are ideas in the link. https://www.google.com/search?q=turn+the+bottom+half+of+the+agitator%2C+either+direction ..

Older models are easy. Connect the 2 wires together and bi pass the switch. Some washer use magnets if so do the same. I’m not sure about new washers.

possible power transformer bas on washer

google from manufacturer or go inside unit there should be a instruction book in by motor

check belt to motor if ok try under agitator the cogs are worn so replace them

possible bad drive motor thats overloading

The door switch is defective. It stops the machine from spinning when the lid is opened. Go to repairclinic.com for help and parts

Washer - Resetting the Electronic Controls - All GE Appliances ...

https://products.geappliances.com > appliance > gea-sup... To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a ... ..

Check to make sure that the washing machine is fully plugged in and then next, check to see if there is a tripped circuit breaker. Reset the breaker and try to turn on your washing machine and try to start the washer.If it still is not turning on then it is a damaged power cord that needs to be replaced.