20 Most Recent GE WSM2420T Top Load Stacked Washer / Dryer - Page 9 Questions & Answers

Could be a defective cycle timer

need same solution, please post

behind the timer knob if you pull it out you will see a plastic horse shoe shaped pin clip that holds the knob on the shaft. could be a very cheap fix if it has broken or worn so that it does not let the shaft all the way out.

Could be the water level sensor is bad and the machine thinks it is full when it is not. Could also be a bad timer.

One of the things to check is the door latching mechanism. It may just be loose. The numbers you provided are for the pedestal and not the actual machine.

Perhaps the drum suspension is worn or broken?

Anxiety as regards social woes which somehow or other are a consequence of gambling games prevents statesmen from any steps in reference to revision of the law about gambling business. Dean Morgan Leather Jackethttps://www.topcelebsjackets.com/product/jeffrey-dean-morgan-walking-dead-negan-jacket

Washer won't run. Display says "H2O Supply" and sounds like it's trying to pump out; water is on, household water supply is good. ... With good water pressure then you have a faulty circuit board that needs replaced. https://www.justanswer.com/appliance/8m26u-ge-gtwn7450d0ww-top-load-washer-display-says-h2o-supply.html

First try to unplug the washer for 2 min. Usually that will solve the problem. If not come back and reply

Replace the control pane

If the Fill light is flashing or H2O SUPPLY is scrolling on the display (2015 and newer models): the washer will initiate a 3 or 4 minute lock-out period (depending on model). The washer controls won't respond or change during this time. After 3 or 4 minutes, you can choose your settings and press Start. Unplugging the washer will start the 3 or 4 minute lock-out period again.

I have just received my 3rd paycheck which said that $16285 that i have made just in one month by working online over my laptop. This job is amazing and its regular earnings are much better than my regular office job. Join this job now and start making money online easily by just use this link......HER? www.bayusd11.com

Hi, There should be a chrome label on the back of the machine, some times on the sides. Thx

There's a part under the agitator that lifts off if you pull up from the bottom on both sides) called a coupler that is attached to the shaft with one bolt. The plastic teeth probably have stripped off from this coupler, causing the agitator to not agitate properly.I would buy the part on amazon.Here's the link to the exact part:shorturl.at/oxDX0Video to show how:https://youtu.be/PN4Q-VqyReo

First make sure someone didn't turn off the supply valves where the washer hoses are attached to. If both are on, then try to fill machine and switch between hot and cold water. If one of the 2 temps works, the other half of the fill valve is bad. The fill valve is the part where the hoses attach to the back of the machine. It is a 2 part electric valve with 2 electric coils on the valve. Could be one coil is bad or possibly the filter screen is blocked on one side. Screens can be checked and looked at by removing hoses and looking inside end of valve. If coil is bad, complete valve needs replaced. Easy exchange, a few screws, 4 wires, and a small hose leading to inside of machine.

Owner's Manual https://products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-90315-2.pdf

Door Switch or a fuse is bad.

Timer may be shot..

E43 is for "excessive drive system brake time"

Reset with
1) unplug 3 seconds,
2) hold Power & Start to display "Jr",
3) cycle thru using the Custom 2 button (3 times) to display E43,
4) hold Power & Start to clear code to E00,
5) stop.