20 Most Recent GE WBSE2090A Top Load Washer - Page 6 Questions & Answers

The main drive motor has a relay switch on the side of it. The clicking and power flicker along with only the first couple of cycles are a good indication if a bad motor relay.

hey this soundslike your washer might be syp[hening out your water which means that the drain hose is lower than the washer.another soluthion might be leakage,how high ias the hose or is there any water on the floor? good luck

check your knob and sleve on the timer to see if they are the right ones or if they line up. if they doit might be the pin in side the timer.or it might be faulty. another suggestiion is check everything out twice. good luck

sounds like you have an advanced problem.might be a bad or stuck timer.

hello, if you washer is not or isn't fully draining that sounds like something might be in the pump.Icheck for any hose blockage as well.If there is a bad smell that might be dirt or a peice of clothing or anything. so my suggestion is to check your drainage hose, the pump or maybe try even to syphan out the pump which means put the drainage hose in a bucket lower than the washer or your drainage is higher than the washer. good luck...

TRY REMOVING FRONT OF WASHER YOU WILL SEE 4 SHOCK LIKE PISTONS TAY GET DRY AND MAKE GRINDING NOISE OR SQUEEKS LUBERCATE ALL REAR HARD TO GET AT MAKE SURE YOU GET TOP AND BOTTOM (RAY)

you didn't say if the machine had filled up with water and stopped after that, if that is so then the place to check first is the heater element for open circuit, this will be located at the bottom end of the drum area, remove plug before testing, work safe, hope i have helped a little, if the machine has not finished filling check the water supply first then the water solenoids. hope i have helped, if so rate me please

No there’s no brushes for GE handmixer

It sounds like the clutch is slipping https://www.google.com/search?q=GE+WSLP1100A0WW+not+agitating

Top Load Washer - Fills But Will Not Agitate

GE Appliances https://products.geappliances.com > appliance > gea-sup... If the lid switch probe or magnet is missing or damaged, the washer will not agitate or spin, even with the lid closed. Missing: WSLP1100A0WW ‎' Show results with: WSLP1100A0WW

SOLVED: GE WSLP1100A0WW not agitating

Fixya https://www.fixya.com > ... > Washing Machines > GE 17 hours ago - Ge top loader washer agitator does not work To check the agitator. Start the washer into wash cycle. Once started Push down on top of agitator.

Ge Washing Machine - Washer Won't Spin Or Agitate

Repair Clinic https://www.repairclinic.com > RepairHelp > Ge-Washe... If a washer is not spinning or agitating, you should first determine if the drive motor is running and if power is reaching the drive motor. If no power if ... ..

Hello Heather Good to see you again. Also check the small strainers on the water connectors. They can block up with limescale and debris. While the connectors are off, turn on the water into a bucket or a sink. You should have a VERY powerful jet of water. Anything that will reduce flow will lengthen the fill time and therefore to total wash time due to fill and rinses. When it pumps out, also check you have good flow in the drain hose and items can jam in the ridges and catch lint enough to block them almost completely. One clever thing to do is whilst the water inlet connectors are off, unlock the drain hose, unhook the part that makes the hook, put the round connector in the hose and wrap a tea towel around it. Get someone to turn the water on full bore whilst you are gripping the two hoses together. Run it for a full minute. Water will be flushed into the machine through the pump in reverse. Put everything back and run a rinse and spin with nothing in it, look at all the black lint that is pumped out! I did that once at work and found an apple stalk that had lodged across the ridges of the drain hose which had 90% blocked the pipe. ..

If your inlet valve itself is stripped then you have to replace the valve. The plastic thread is part of the inlet valve. If its only the screen in your inlet valve you can remove the screen and replace it. However if you crossthread anything plastic it HAS to be replaced.

If you give me your model number of the washer usually the wpl 4318046 can be used as an inlet valve which is a cheaper alternative than your local parts distributor would tell you. GE parts on avg are 30% more expensive than anything else. On ANY ge appliance there is usually a way around there replacements with some minor altercations. I wish this site had a way you could contact me directly. I just joined so am not an expert yet but ive done my time in the field. If i could give you any expert advise its DONT BUY GE, OR LG.

Let me know if this helps.

Question edited for clarity 'MAKE model (WHAT IT IS)'. You posted to Televisions, moved to GE Washing Machine. It may be the lid lock, test it with your digital multimeter. Look for loose or damaged connections. https://www.google.com/search?q=GE+Gtw330ask0ww+not+running ..

check under agitator possible worn cogs

check voltage to pump if ok bad pump also check drain hose

Check the water level sensor.

Just remove the drain hose from the drain upstand pipe and lower it to the floor. It will empty the pump or water.You can also drop a pint of car anti freeze into the machine just to be sure if you wish.

You likely have a water leak spraying onto electrics, or the water inlet valve is shorting out.

Remove the bottom impeller and clean out the water proof grease that has come out of the seal and drive shaft.

I understand your frustration. It sounds like your GE washing machine is having some problems. Resetting the washer may help to fix the issue. Here are the steps on how to reset a GE washing machine WPDH8900J1WW: 1. Unplug the washer from the power outlet. 2. Wait for 2 minutes. 3. Plug the washer back in. 4. Turn on the washer. 5. Select a cycle and press the start button. If the washer still does not work, you can try resetting the drum motor. To do this, follow these steps: 1. Unplug the washer from the power outlet. 2. Wait for 1 minute. 3. Plug the washer back in. 4. Open and close the lid of the washer 6 times within 12 seconds. 5. Close the lid and press the start button. If the washer still does not work after resetting the drum motor, you may need to contact a qualified appliance repair technician. Here are some other things you can try before resetting the washer: * Make sure that the washer is properly leveled. * Check the water supply hoses for leaks. * Clean the lint trap. * Check the detergent dispenser for clogs. I hope this helps!

Please see the following link for the error codes https://www.youtube.com/watch?v=JglsX87UdeY&pp=ygUvSG93IHRvIGdldCBpbnRvIHNlcnZpY2UgbW9kZSBvbiBteSBHRSBHRldOMTYwMD8%3D