20 Most Recent GE S8000E - Page 3 Questions & Answers

The light is part of the diagnostic system. This is an internal systems light that flashes all the time and is an indication that everything is operating normally.

When you took the hot water hose off, did you check the little gauze strainer inside where the hose screws? That black in the water is iron and scale from the hot tank. See the video I added. Cleaning the filter https://www.google.com/search?q=ge+profile+top+load+washer+clean+filters Videos for removing the agitator https://www.google.com/search?q=ge+profile+top+load+washer+remove+agitator Buzzing could be the motor or controller knob, but if its' running, don't worry. https://www.google.com/search?q=ge+profile+top+load+washer+buzzing+noise Screeching is normally belt slip. You can get a can of belt conditioner which makes it supple and grippy. A GE washer making noise that sounds like squealing likely has a damaged drive belt. This rubber belt is suspended on a pulley, connecting the tub to the drive motor or transmission in front and top load washers. Wear and tear can cause the belt to loosen or fray, resulting in a squealing sound. May 1, 2021

Why Is My GE Washer Making Noise?

it might spin off try holding drum and turning

It sounds like there may be an issue with the drain hose on your GE 465 top-load washer. The fact that the drain hose is wet halfway up suggests that there may be a leak in the hose. This could be caused by a hairline crack or a problem with the connection between the hose and the drain outlet. One possibility is that the extra rinse option and the maximum water level setting on the tub caused a higher volume of water to be drained through the hose, which may have caused an existing issue with the hose to become more pronounced. Another possibility is that the internal drain pump is not functioning properly and the water is not being pumped out of the machine properly, causing the overflow. It is recommended to contact the manufacturer's customer service or a professional technician to have the washer inspected and repaired. They can check the hose and connections, and also the drain pump to determine the cause of the problem and fix it accordingly. It's important to keep in mind that attempting to repair a washer can be dangerous if you're not familiar with the proper procedures and safety precautions. It's best to let a professional technician handle the repair. Regenerate response

The hose could be kinked or have a hole in it for the washing machine and you need a new hose as well for your washing machine..Or the drain pump is bad or the tub to the pump hose is not working.

If the inlet on your GE washer has been stripped or cross-threaded, it may be necessary to replace the inlet to repair the problem. To replace the inlet on your GE washer, you will need to follow these steps:

1. Disconnect the power to the washer by unplugging it from the wall outlet or turning off the circuit breaker that supplies power to the washer.
2. Shut off the water supply to the washer.
3. Remove the hoses from the inlet by loosening the hose clamps or fittings that secure them to the inlet.
4. Remove the screws or bolts that secure the inlet to the washer.
5. Carefully lift the inlet out of the washer and set it aside.
6. Install the new inlet by reversing the above steps. Make sure to connect the hoses to the correct fittings on the new inlet.
7. Turn the water supply back on and check for any leaks.
8. Restore power to the washer by plugging it back into the wall outlet or turning the circuit breaker back on.
9. Test the washer to make sure it is filling properly with the new inlet.

Note: These instructions are general guidelines and may vary depending on the specific model of your GE washer. If you are unsure of how to replace the inlet on your washer, it is recommended that you contact a qualified appliance repair technician for assistance.

If you have replaced the door lock on your GE washing machine and it is still not working properly, there could be a few different causes for the issue. Here are a few things you can try:

1. Make sure the door lock is properly installed and aligned with the latch on the door.
2. Check the wiring between the door lock and the control board to make sure all connections are secure and there are no damaged wires.
3. Test the door lock with a multimeter to see if it is receiving power and functioning properly.
4. If the door lock is receiving power and functioning properly, the issue may be with the control board or another component in the washing machine. In this case, it may be necessary to take the washing machine to a repair shop or contact the manufacturer for further assistance.

It is also a good idea to make sure that the door lock is not being activated by any foreign objects or debris that may be preventing it from functioning properly.

need the Model number to help you find the white tag and add the model number it inside the front door frame

Breakers trip if there is a dead short to earth or if something in the appliance has high resistance and is drawing more amps that the breaker. This can happen with failing elements. However F72 is leading towards a control board issue. This needs professional diagnosis as they are expensive. https://www.google.com/search?q=GE+ZET1FH1S+Wall+Oven+Error+code+F72 ..

First thing to do is unplug it for 5 minutes and see if it resets.

if good pressure at solenoid possible calcium build up in lines

check belt under unit if ok check under agitator for bad cog splines

Hi, please power cycle your washer in order to move forward. If that fails, please switch cycles (ie rotate knob)without starting and then attempt to unlock the lock. Thank you.

Our GE top-load washer would sometimes quit before the spin cycle. It would make 2 or 3 loud clicks and quit. Other times it worked fine. Problem was with the lid lock. On the lid there is a loop that fits into a slot in the washer top when the lid is closed. That loop is magnetic. Somehow, a small safety pin got magnetically attached to the back side of the loop. Washer works fine with the safety pin removed.

Hi, please check your GE manual to determine the status of light is normal or not. Thank you.

check belt if ok check cogs under agitator

https://youtu.be/II_p8j-RSWU

My washer is doing the same thing. I just ordered the new peice and still won't stay on. They say line up the groves which I did, but still comes off

This suggests a communication issue. https://www.fixya.com/support/t29731810-ge_fridge_displays_0000 Call a local GE refrigeration engineer. There is a video if you want to try some things. https://www.google.com/search?q=Ge+model+pfss5rkzhss+is+flashing+0+on+the+control+panel ..

Ceck for a leak on the outlet pipe fitting.