GE S8000E - Answered Questions & Fixed issues

It is possible that the belt at the back of the machine is slipping. try running the spin cycle without any load in the machine. I assume this is a front loading machine and you are in UK. the Belt is available on line for about 15 pounds. If it is running the washing cycles normally, it can't be the motor.

I had the same problem. My husband checked the carbon brushes attached to the motor and ran the machine on spin. The brushes were sparking so he assumed they were worn and replaced them and hey presto machine works fine now. The brushes cost 23.99 and were just bought from a local shop but can be bought online cheaper. Hope this helps solve your problem. Essex

usually crease guard is a combination of hot and cold (warm depending on water temp and water pressures)

Hoover fast wash is generally a shorted time cycle of the normal washes

Clean the pump filter and check the pump motor impeller.

Should you have to use un due force to get the filter undone on the Hoover 1300 special deition washing machine

No there’s no brushes for GE handmixer

It sounds like the clutch is slipping https://www.google.com/search?q=GE+WSLP1100A0WW+not+agitating

Top Load Washer - Fills But Will Not Agitate

GE Appliances https://products.geappliances.com > appliance > gea-sup... If the lid switch probe or magnet is missing or damaged, the washer will not agitate or spin, even with the lid closed. Missing: WSLP1100A0WW ‎' Show results with: WSLP1100A0WW

SOLVED: GE WSLP1100A0WW not agitating

Fixya https://www.fixya.com > ... > Washing Machines > GE 17 hours ago - Ge top loader washer agitator does not work To check the agitator. Start the washer into wash cycle. Once started Push down on top of agitator.

Ge Washing Machine - Washer Won't Spin Or Agitate

Repair Clinic https://www.repairclinic.com > RepairHelp > Ge-Washe... If a washer is not spinning or agitating, you should first determine if the drive motor is running and if power is reaching the drive motor. If no power if ... ..

Hello Heather Good to see you again. Also check the small strainers on the water connectors. They can block up with limescale and debris. While the connectors are off, turn on the water into a bucket or a sink. You should have a VERY powerful jet of water. Anything that will reduce flow will lengthen the fill time and therefore to total wash time due to fill and rinses. When it pumps out, also check you have good flow in the drain hose and items can jam in the ridges and catch lint enough to block them almost completely. One clever thing to do is whilst the water inlet connectors are off, unlock the drain hose, unhook the part that makes the hook, put the round connector in the hose and wrap a tea towel around it. Get someone to turn the water on full bore whilst you are gripping the two hoses together. Run it for a full minute. Water will be flushed into the machine through the pump in reverse. Put everything back and run a rinse and spin with nothing in it, look at all the black lint that is pumped out! I did that once at work and found an apple stalk that had lodged across the ridges of the drain hose which had 90% blocked the pipe. ..

If your inlet valve itself is stripped then you have to replace the valve. The plastic thread is part of the inlet valve. If its only the screen in your inlet valve you can remove the screen and replace it. However if you crossthread anything plastic it HAS to be replaced.

If you give me your model number of the washer usually the wpl 4318046 can be used as an inlet valve which is a cheaper alternative than your local parts distributor would tell you. GE parts on avg are 30% more expensive than anything else. On ANY ge appliance there is usually a way around there replacements with some minor altercations. I wish this site had a way you could contact me directly. I just joined so am not an expert yet but ive done my time in the field. If i could give you any expert advise its DONT BUY GE, OR LG.

Let me know if this helps.

Question edited for clarity 'MAKE model (WHAT IT IS)'. You posted to Televisions, moved to GE Washing Machine. It may be the lid lock, test it with your digital multimeter. Look for loose or damaged connections. https://www.google.com/search?q=GE+Gtw330ask0ww+not+running ..

check under agitator possible worn cogs

check voltage to pump if ok bad pump also check drain hose

Check the water level sensor.

Just remove the drain hose from the drain upstand pipe and lower it to the floor. It will empty the pump or water.You can also drop a pint of car anti freeze into the machine just to be sure if you wish.

Remove the bottom impeller and clean out the water proof grease that has come out of the seal and drive shaft.

You likely have a water leak spraying onto electrics, or the water inlet valve is shorting out.

I understand your frustration. It sounds like your GE washing machine is having some problems. Resetting the washer may help to fix the issue. Here are the steps on how to reset a GE washing machine WPDH8900J1WW: 1. Unplug the washer from the power outlet. 2. Wait for 2 minutes. 3. Plug the washer back in. 4. Turn on the washer. 5. Select a cycle and press the start button. If the washer still does not work, you can try resetting the drum motor. To do this, follow these steps: 1. Unplug the washer from the power outlet. 2. Wait for 1 minute. 3. Plug the washer back in. 4. Open and close the lid of the washer 6 times within 12 seconds. 5. Close the lid and press the start button. If the washer still does not work after resetting the drum motor, you may need to contact a qualified appliance repair technician. Here are some other things you can try before resetting the washer: * Make sure that the washer is properly leveled. * Check the water supply hoses for leaks. * Clean the lint trap. * Check the detergent dispenser for clogs. I hope this helps!

Please see the following link for the error codes https://www.youtube.com/watch?v=JglsX87UdeY&pp=ygUvSG93IHRvIGdldCBpbnRvIHNlcnZpY2UgbW9kZSBvbiBteSBHRSBHRldOMTYwMD8%3D

OL = Overloaded. Is the Washer overloaded? If OL (overloaded) appears in display, the load too large. If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent.Feb 24, 2020

OL - Error Code - Top Load Washer - Product Help - Maytag

Maytag https://producthelp.maytag.com > ... > OL

The washer has ol on it at the end - Maytag Bravos quiet ...

iFixit https://www.ifixit.com > Answers > View > The+washe... Oct 6, 2014 · 2 answers First, OL stands for "Overload", so in other words, the washer thinks the tub is too hard to move because it's overloaded and the motor is ... OL code all the time even with very small and light ... 2 answers Sep 28, 2016 Why washer stops and gives code "ol" - iFixit 2 answers Nov 30, 2016 at the end it says OL - Maytag Bravos quiet series 300 ... 1 answer Dec 29, 2022 OL code showing . - Kenmore 110 Series Washing ... 2 answers Sep 19, 2017 More results from www.ifixit.com

A top-load washer tub is usually supported by four suspension rods. If one of the suspension rods becomes dislodged or breaks, the control board may stop the spin cycle several times to try to balance the clothes. Suspension rods will often come in a set of four and it is recommended to replace all four of the rods at the same time to reduce uneven wear.