20 Most Recent Kenmore 44921 Front Load Washer - Page 2 Questions & Answers


I don't know, but I would assume it is an AC solenoid so it does not matter. If the wires are the same color, that would be a safe bet. If they are different colors, you may need more research. NORMALLY, there is a schematic inside the unit, for technician use only. Go for it.

Kenmore Washing... | Answered on Nov 07, 2019


Check the washer outlet by plugging in a lamp if the is power at the washer turn the dial to different setting and see if it turns on. Make sure the lid or door is closed

Kenmore Washing... | Answered on Nov 03, 2019


Kenmore 110 washer capacity
Washer. The Kenmore 70 series washer has a 3.5 cubic foot capacity. It comes with the Sears Triple Action agitator and can hold 28 extra-large t-shirts in a single load.

Kenmore Series 70 Specifications ' Hunker

Kenmore Washing... | Answered on Oct 18, 2019


Have you tried unplugging it from the hydro? It may just need to reset itself.
All machines nowadays are like computers, and need a reset every now and again. Since they don't have a reset button, it may help to unplug power and leave it unplugged for 5-10 minutes.

Kenmore Washing... | Answered on Oct 14, 2019


the error code "OE" is a "Drain error " and it is initiated by your washer not having fully drained in 10 minutes.
Most common cause is a clogged filter. Check your "coin trap" filter for retained objects, like missing socks etc.:-)
To clean it
1. Take off the lower front panel
2. Turn the pump filter cover counter-clockwise by hand and remove. Place a bucket or pan underneath it since you will get water spilling out of there.There will be plenty of water. So please make sure that you have lots of buckets and towels etc. to catch the water
3. With a set of long pliers, remove the filter. Clean that of any debris etc. and replace it when cleaned.
4. Replace the filter cover and lower panel.
Or;
Check the drain line for obstructions by moving it up and down quickly like a water ram.

Kenmore Washing... | Answered on Oct 12, 2019


i don't know. for drain, if in a stand pipe, it seems the drain pipe may be partly blocked. if hooked hose runs into sink, sink drain may be partly blocked, if drain water comes out too fast, consider a tywrap to hold a small towel around hose end to stop splashing. do not block the hose outlet.
low hot water flow may indicate supply hose is restricted. please shut off both cold and hot water supply . remove and inspect hot water hose for blockage. some hose have a screen filter in the end that needs cleaning.
if practical, connect the hot water hose to the hot tap and run water into sink to test for a good flow.

Kenmore Washing... | Answered on Oct 12, 2019


I do not know about a Kenmore but all the washing machines I have taken apart have a pressure switch located near the top just under the lid. as the water fills the machine it also fills a plastic pipe which is connected to the pressure switch.

Kenmore Washing... | Answered on Oct 09, 2019


If it fills with water and will not start agitating or the spin cycle check the safety switch on the lid, they vibrate loose and fall out

Kenmore Washing... | Answered on Oct 09, 2019


washing machine or stove get it in the proper category but sad to say you will probably never find one

Kenmore Washing... | Answered on Oct 08, 2019

Not finding what you are looking for?
Kenmore 44921 Front Load Washer Logo

22 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5692 Answers

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenmore Washing Machines

  • Kenmore Washing Machines

Most Popular Question

water not completeing draining

  • Washing Machines
Loading...