Top 20 Motorola Mobility RAZR2 V9m Questions & Answers

hi good day and welcome to fixya service
here is my solution since your phone has not been used for about a year usually the cause is loose contact at the charging port, turn off the phone then try to spray with electronic contact cleaner then wait to dry for about a minute. now after a while plug your charger make sure the charger is working fine then observed if it works. now if still doesn't charge, if you don't have enough tools and device, for safety just send it to the cellphone repair shop they have enough tools and equipment to replace parts. the charging port might need to replace and the charging IC need for check up. hope this will help thanks for consulting.

Enter 000000. Cheers

hold the smart key( the one on the left side of the phone - the lowest one.Cheers

im most cases it a short in the mobiles power charge relay and it needs to be replaced by a mobile tech in slight cases it can be a bad battery try another battery just to see if it charges but as we mainly see the relay as the problem i think thats your cause


sorry


merry christmas

you need a new LCD and the professional Tech to change it because It is very easy to damage the Flexible cable that adhesived to in -LCD and out - screen. Good luck

Hi,

Basically only your display is damaged/broke.So all your functions are working well.Please replace the display with the new one so that everything will be fine.

To replace please go to nearest motorola authorized service centre.They will replace the screen for you.

thank you

One fun way to customize a cellular flip phone like the motorola razr2 v9m is by replacing the housing with one of a different color or design. Many people don't know that this can be done without the help of a service technician. In fact, you can change the phone housing on your motorola razr2 v9m by yourself in less than an hour.

Things You'll Need:

• Small Phillips screwdriver
• Tweezers

Turn off your motorola razr2 v9m, flip it closed and turn it over. Press the battery latch on the top of the phone down and slide the battery compartment cover off of the back of the phone. Lift the square battery out of the phone and set it aside.

Use your small Phillips screwdriver to remove the two screws located on either side of the battery compartment.

Use your fingers to gently pry the lower panel off the back of the device. Be careful as it will still be connected to the phone via a ribbon cable. Use your fingers to unplug the ribbon cable where it connects to the side.
Turn the back panel over and you will see the motherboard and speaker assembly housed in the back panel. Use the tip of your screwdriver to pop up the two clips on either side of the bottom of the motherboard and release it. Then lift the motherboard out of the panel.
Use your tweezers to lift the black speaker from its circular compartment in the bottom of the panel. Then, fit the speaker in its compartment in the new back panel. Place the motherboard over the speaker and secure it in place by pushing down on the tabs on the corners of the motherboard.
Locate the back of the mouthpiece, at the bottom of the phone, just under where the back panel used to sit. Use your screwdriver to remove the four screws holding the panel in place and remove the mouthpiece by pulling it gently away from the bottom of the phone.

Use the tip of your screwdriver to pry up the four tabs (two on each side) that hold the keyboard in place. Turn the phone over and lift the keypad away from the device.
Place the keypad in its place in the new front housing and press the four tabs on the back of the housing down to secure it. Slide the new plastic mouthpiece in at the bottom of the new housing. Replace the four screws on the back of the mouthpiece.
Replace the back panel, making sure to connect the ribbon cable to the side of the new housing. Replace the two screws just above it, on either side of the battery compartment, replace the battery and new battery cover, and you are done.

LCD is not working and need the new one.

The connector between the main circuit board and the LCD could have been damaged, like what the other person said, it's common to flip and slide phones.

My guess is that the charging port in your phone has gone bad. By holding it a certain way, you may be reconnecting it just enough to make the connection. Probably have a loose or broken wire inside your phones port. You may also see this is a problem if you try to hook it up to a pc.

www.modmymoto.com can help you..its there

Here is the full user guide for your phone, it is in PDF format, so you may need Adobe PDF installed if it isnt already.

http://support.sprint.com/global/pdf/user_guides/motorola/motorazr_v9m/motorazr_v9m_by_motorola_ug.pdf

Hope this helps

replace the battery..

see it at the right side of the back panel..

there a small slot in there..open it...

The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries. Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use any photo management program such as Picasa ( http://picasa.google.com ).

What is the exact model number to your Sanyo TV?

All astronomical telescopes show the view upside down (and some have right/left inversion too) For terrestrial views, a erect image adapter is available but NOT recommended for astronomy as they reduce contrast.

You were asked questions? I have been campaigning for this for 3 months. I told them you need a pop-up All questions need 'make model (what it is)' as first 3 words. You are missing the maker, but you do mention 'shredding'. Then I also said 'There are 40,000 categories to choose from'. You chose 'Cell Phones'. and it's not a 'memo', it's a question. :>) So, first of all, disconnect it from the mains for 30 minutes. If you jammed it, you were working it hard, and when it jams, heat builds up in the motor and trips the thermal protection device. They have a thermal cut out, some have a thermal fuse what need physically replacing, but most reset when they cool. Does it work in reverse? A jam can sometimes damage the switch in the throat of the shredder, some are a mechanical switch, some are an infra-red sensor. https://www.google.com/search?q=DM72C ..

There doesn't seem to be anything online to suggest how to do a reset or recalibrate the screen. You could try three things Look for a tiny Reset hole in the back. Connect it to a computer and in Windows Explorer see if the is any useful right click commands? Or leave it running until it runs out of power, wait 24 hours before recharging. ..