There is usually a tube next to the drum that has a sensor on it and that tube fills with water. It can get plugged up with softener or debris and then the machine wont be able to tell when it is full. To get to the tube, you must remove the tope of the machine.
Question edited for clarity.
You mean the clothes are still damp, (not dried enough) or that are as wet or wetter than you put them in? Bad dryer sensor for the former, broken water inlet valve or heater element failure for the latter.
With combined washers and dryers, there are so many things that can go wrong due to the number of sensors involved. You will need a service call from an LG technician.
If the washing machine is not coming on check to see if the child lock feature has been turned on.Try to reset your washing machine by unplugging the washing machine then press and hold the power button for at least 5 seconds to restart your washer.
Hi, I purchased the same machine. My repair man speaks about the mother board. I would like to purchase it on line, since where I live there aren't any available. How can I find the exact part that I need for this model?
F10C3LDP2 LG
There is not a lot of info on the unit. Tip it up and see if there is an open bottom to access the drain and pump. If not then the top pops off, be careful not to damage the paint. Then you remove the screws that hold the front on and you should be able to get to the pump
Question edited for clarity.
This model is exclusive to South Africa. This link should work local to you as we are in North America. There is a spares outlet listed and the service manual is in the link.
https://www.google.com/search?q=LG+wd-10165f+parts
..
When you do hear your LG washing machine making a loud banging type of noise on the spin cycle it could be caused by overloading or a loud that is unbalanced Or the bearing has worn out and needs replacement.
Look for a circuit breaker that has tripped Reset the breaker then by turning off your washing machine for a few minutes if it still is not working either the power cord is broken or the control panel is no longer working on the washer and needs to be repaired.
It is a good job I can decipher abbreviations. They don't work well on this site. Please always spell in full Maria.
TO TURN OFF CL CODE ON NEWER LG FRONT LOAD WASHERS: To TURN OFF CHILD LOCK on your LG washer, press and hold the CHILD LOCK button for 3 to 5 seconds. The washer should now have CHILD LOCK mode DISABLED and all buttons will function properly.Aug 13, 2019
Take the back off and check the belt it may have some of the rubber removed on the belt and as it goes around it clicks as it slaps against the drum or around the motor pulley.
Good luck
Not sure but it could be a bad motherboard or the pipe that comes off the bottom of the drum and then goes up to the circuit board to turn the water off when it fills to the right level. Does the water turn on as the washer is washing like halfway through it cycle if cycle if it does water is leaking out of the washer maybe and it refills until it gets up that pipe and makes that sensor on the circuit board and it keeps refilling and refilling and that's what takes so long for the washer to finish his cycle.
Good luck
Sounds like you should buy a water filter to put in your house or wherever line to filter the water. it can be a cheap one with just a cheap paper filter to keep out any sand or settlement especially if you are on a well oh sounds like the valves are getting dirty inside and not closing completely because of debris in the valve.
The small black tube needs to be replaced and the hose needs to be replaced for the washing machine part and the duct and the air vent could be having to be replaced for the dryer or the heat is not working properly.
Mildew is caused by leaving the machine damp and with the lid closed. You should dry the machine after every use. Once you have it is it hard to get rid of it. Vinegar is not good for the removal of it. Boil washes with bleach is a good solution. Also, go to Home Depot and get a bottle of Tilex. Spray it all around the inside of the machine and leave it for a couple of hours. Then do it again and leave it overnight. Then do a wash. Tilex is made specifically for mold and mildew on tiles.
