Top 20 Panasonic SC-BT200 Home Theater Systems. Single-disc 1000W Blu-ray Disc home theater system Questions & Answers

I am not sure about the d5/5 error but you should be able to eject the disc by performing the following, which I took from my user manual. Turn off the unit. Press and hold the [ >>/>>' ] and [ OPEN/CLOSE ] on the main unit at the same time for about 5 seconds. Hope that helps. Paul

What is the problem? For more information, or should you have more questions, please visit my website at audioserviceclinic.com. You may contact me directly through the website. Thank you.

Go to panasonic website or check operation manual

See page 39...

Register and download the manual for free at retrevo.com

http://www.retrevo.com/support/Panasonic-SC-BT200-Home-Theater-Systems-manual/id/23459dj389/t/2/

cant open or close dvd player.says locked.can use remote to play etc but cant open to change dvd

Hello there,

Yes it is possible and relatively simple to do. I suspect you have only connected an HDMI cable from the Home Theater system (HT) to the TV. This cable only sends audio and video to the TV from the HT system - it can't be used to receive the audio from the TV back to the HT.

To get audio from the TV channels through the HT speakers, you will need to connect a separate audio cable from the AUDIO OUT sockets on the TV to the HT. This can be either a Digital Optical cable (connects to socket ringed in green) or an RCA type stereo audio cable (connects to AUX sockets ringed in red).



If you are using a cable or satellite receiver, you should connect the receiver directly to the HT rather than the TV. You would also need to select the correct INPUT on the HT when you want to use the speakers for the TV channels. This will be DIGITAL 1 if using the digital optical cable or AUX if using the RCA stereo audio cable.

The audio connections are explained on page 16 of your user manual and input selection is explained on page 23. If you don't have a manual, please let me know and I can supply one.

I can draw you a diagram showing how to connect your TV to the HT and provide step-by-step instructions for setting it up, but you will need to let me know the brand and model number of your TV. If you are using a cable or satellite receiver, please let me know the brand and model number of this receiver as well.

Hope this helps.

Regards,
BElectric

the firmware update for sc-bt200 & sa-bt200 takes approx 10 mins. the box will display UPD5/5 - this process takes about 10-15 minutes, the box will switch off automatically. Leave for 30 seconds, and power on manually with your remote control - the screen will display - "firwmware update completed.".

What kind of TV do you have?
I have found one of the easiest ways to connect surround system is to connect all your accessories (ie. Wii, Cable Box, VCR, etc) to the TV.

Next find the AUDIO OUT on the TV and connect this to the TV or AUX input on the home theater.

Tune the Home theater to the Input that you connected the TV to. This should play the audio through the home theater for any input you tune the TV to.

Note: make sure to turn the TV volume all the way down otherwise there will be some distortion due to the delay between the TV and the home theater.

Good Luck,
Robert

I hope I understand you correctly.

As you can probably tell from the very different connector types on the subwoofer and the HTS, they don't match up. That speaker system and this electronics are not meant to be used together.

The SC-BT200 uses passive subwoofer while the SB-WA342 is an active (powered) subwoofer.

http://www.retrevo.com/support/Panasonic-SC-BT200-Home-Theater-Systems-manual/id/23459dj389/t/2/

According to the manual the speaker cables are as follows...

1 Speaker cable (center)

[REEX0858-L (green)]
2 Speaker cables (surround)

[REEX0860E-L (blue)]
[REEX0868E-L (gray)]

2 Speaker cables (surround back)

[REE1488 (brown)]
[REE1489 (tan)]

The only things that makes them unique are the unique molded connectors. Hardly $166 worth. You could buy a 100' roll of 18-gauge speaker wire or lamp cord and 5 molex connectors at Radio Shack for a lot less.

If you took the base unit in I'm sure they could help you find a compatible connector and pins.

Hi,
Please follow the steps : To change the player region code
1. Be sure players drive is empty (nodISC)
2. Enter following key sequence using remote control:

Enter, 6, >=10, <<, 00F2, Audio, 8, * requested region code here (1-8) *, Subtitle, 1

3. Player will reset and requested region code will be set.
- For example to set region code to 3 press: "Enter, 6, >=10, <<, 00F2, Audio, 8, 3, Subtitle, 1"

To set the player to RCE proof region free
1. Be sure players drive is empty (nodISC)
2. Enter following key sequence using remote control:

Enter, 6, >=10, <<, 00F2, Audio, 8, 1, Subtitle, 4

3. Player will reset and set to "region-free" and "RCE-free" mode

To restore players factory region code
1. Be sure players drive is empty (nodISC)
2. Enter following key sequence using remote control:

Enter, 6, >=10, <<, 00F2, Audio, 8, 9, Subtitle, 1

3. Player will reset and set to factory region code
Regards, Jay__g6

Hi, kindly get the code here : www.regionfreedvd.net/ www.dvdripper.org/dvd-region-codes-vs-ntscpal/ www.regionfreedvd.net/players.html
www.dvdreviewer.co.uk/Forums/...region_code/page1
Best Regards, Jay__e45r6

I had this problem myself after a firmware update. Tried everything, unplugging power, disconnecting internet. Then I tried connecting my iPod. When I disconnected my iPod it suddenly started up again. Problem solved!

ps I am writing this just after I solved it. It appears to be updated. I am now trying out Youtube which works well.

check first the region compatibility of you player and the DVD disk next clean the lens of your player open the cover of the player,using a cotton buds gently wipe the lens of the player..be sure the unit is unplug before operation...tnx.

First on your both devices. Your blu ray player & your laptop for signing in to netflix then goto my account & help then scroll down you get activate a netflix device then click you see the activation code. Paste this code into your Sony blu ray player netflix account.

Cannot eject disc. ≥The unit may have a problem. While the unit is off, press and hold (>> / >>I) and (< OPEN/CLOSE) on the main unit at the same time for about 5 seconds. Remove the disc . After disc removal or if this does not work you may need to reset to factory defaults. for the player alone.

To return all settings other than some settings to the factory preset.

≥Select “Yes” in “Restore Default Settings” in the Setup menu.

This returns all values in the Setup menu and the on-screen menu, except for “Remote Control Code”, “On-screen Language”, “IP Address/DNS Settings”, “Proxy Server Settings”, “Network Service”, “DVD-Video Ratings” and

“BD-Video Ratings” to the default settings.

If this does not work then you may need to reset everything to the factory settings.

To return to the factory preset. Everything Reset.
(No setting)

≥Reset the unit as follows:

1 Press [POWER] on the unit to turn off the unit.

2 Press and hold (>> / >>I) and press [POWER] and [< OPEN/CLOSE] on the unit at the same time for more than 5 seconds until “PLEASE WAIT” is displayed on the unit.

3 The power is turned on and then turned off automatically.

Cheers!

Hi! Please try this, insert a cd lens cleaner in the cd tray and play it. The lens may be dirty causing it hard to read dvds. Hope this helps and have a good one!

Google for "Panasonic SC-BT200 Region Free

Also see

"http://www.avforums.com/forums/blu-ray-players/885440-blu-ray-player-multi-region-hex-codes.html"

Some Blu-Ray players will need a hardware mod to be region free.

juan, ha podido desbloquear su bluray?

le agradezco cualquier informacion...

sergio ([email protected])

try change to region 0, (all contrys)