Dynex DX-LDVD22-10A 22 in. HD-Ready LCD TV - Answered Questions & Fixed issues

Replace the TMS94481CT transformer on the inverter board. Can't miss it it is bright yellow. Part is available on EBay.

If the unit indicates no disc or disc not read it is likely a dirty or bad optical pickup in the player.

HelloCheck the backlight inverter. It will be faulty.

Sir this problem is coming from the t-con board. This t-con board is the one that transfer image signal to LCD. You can replace it with new one try to check this link for T-CON board http://www.shopjimmy.com/catalogsearch/result/?q=t-con+board good day and best regards.

make sure the antenna is connected to set, I live on the fringes of digital broadcast and had to install a booster to the antenna, seems like you need a little stronger signal w/ digital than analog to get reception. Also check your input that you are scanning.

Try changing the size of the screen by pressing Ratio or Screen size using your remote.

AAA TV Service
http://www.aaatvservice.com

This can be a really frustrating problem, but I hope that you have gotten this resolved. If not, here are some steps that might help you out.

When you are using the RCA cables, you want to connect them on the back of the receiver where there is a green TV symbol with a 1 in it. You will want to make sure that your TV is on channel 3, and then slowly cycle through the inputs. It can take a few seconds for the inputs to change, so wait about 10 seconds on each input. If you still get no picture, try to go to channel 4 and do the same.

When you use HDMI cables, it is close to the same process. You will need to be on an HDMI input. Again, wait about 10 seconds on each input. Try this first on channel 3 then try 4 if you have no luck.

Feel free to email me if you have any other issues!

Becki Barned
DISH Network Customer Service
[email protected]

Here is a direct link to the User's Manual for your TV set:

http://www.dynexproducts.com/cms/documents/DX-LDVD22-10A_09-0042_MAN_V1_ENG_Final%20lr.pdf


To view the Owner's Manual with Operating Instructions just use your mouse to click on the link, which is the underlined and highlighted text just above. This will open a new web browser page automatically for you and allow you to view the information at the website indicated and the contents of the Owner's Manual.

You may need ADOBE READER installed on your computer to read PDF documents.
You can download this free at WWW.ADOBE.COM if necessary.
Click on the DOWNLOAD ADOBE READER button on right side of the ADOBE home page when you get there, then follow the onscreen instructions to install the software on your computer.

See page 13 of the manual for complete instructions on how to adjust the sound settings on your set.

Please comment back here to this page if you have any details to add, have any questions, have difficulty accessing the links, or just require further general assistance and I will respond as soon as I see it.

I hope that was helpful to you, good luck and take care.

Joe.

With that type of TV I would recommend a surround sound system Walmart has there pretty cheap from 35.00 to 235.00 another option would be to use a receiver in the mix, If you have an older type receiver just simply run a mini or mini to dual RCA audio cable to get sound, your speakers can them be connect to the receiver.

Model number?
User manual: http://www.dynexproducts.com/support.html?tab=product
Most of the Backlight level setting should be in the on screen PICTURES setup menu or SETUP menu.
The higher the level the more power is used and also shortened the life of the lamps and the inverter circuits since it will run harder and produce more heat.

Basic LCD monitor and TV troubleshooting guide: http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague Parts: www.shopjimmy.com Parts: http://interliquidparts.com/ Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps. Or www.digikey.com, just make sure to use caps with low ESR, 105c, high ripple current and long life rating such as PANASONIC FM or FC series.

Have you tried turning off the Screen Saver function? Go into the menu and try to reset the system to default settings as well. If you still have questions, here is a link to the manual in case you dont have it.
Still having issues? Drop me a line and i'll be right back with you.
GOOD LUCK AND PLEASE RATE THIS POST!!!

Yes it's cracked inside and there is no fix for a cracked screen, the panel will cost more than the tv new. It's not worth it, verify at vancebaldwin.com

Hopefully it will be the ballast unit that has failed. That is the power supply that powers the backlights.

it means its a porn channel

I had a similar problem with my 42 in Philips LCD HDTV.

Here was the problem. My Power Supply Board had several bad capacitors. I opened my TV (warranty was expired of course) and found four bulged capacitors on the PSB. Many major electronics companies Philips/Magnavox, Sony, Panasonic, and others were sold capacitors that failed in 2-5 years instead of 10-20. The capacitors fail prematurely due to a lack of preservatives. Unfortunately, they were installed in all sorts of devices and cause a wide range of failure problems.

Here are some options for you.

1. Have it fixed by a professional $$$$$$$??????? (Is it under warranty?)

Remember, TVs CONTAIN HIGH VOLTAGE AND CAN KILL YOU! Do this at your own risk.

2. Open your TV and find PSB. (The board that the power cord plugs into) Check for faulty caps. If you find some (bulged or leaking) bad caps replace the entire board. The entire board costs around $250 right now because they are in high demand right now. They can be found online. I would definitely shop around though.

3. Remove and then replace individual faulty caps. This takes some soldering skill.

Caps are inexpensive and if you can take care of it yourself it will save you hundreds.

This may be your problem. If you determine that it might be.

I have a Tip/How TO tutorial on this site that may also help. It gives step by step instructions for replacing caps on PSB #715t2432-2. If this is your board you are in luck. Here is the Link: Fixing the Philips Turns/shuts off on its own problem. I'm working on uploading pictures to help guide people though the process as well. Let me know if I can do anything to help.

Hope this helps and if it does please rate it accordingly. Good luck.

It will be more bothersome but use the buttons on your TV instead od the remote. You should be able to highlight whatever you want with the on set buttons

You can find the remote from this link.

Go to the menu get out the setting, u should get it unscramble.

Is the Dynex a Smart TV connected to the Internet? Generally speaking, they are a budget brand

Solved: Remote won't control Dynex TV

Roku Community https://community.roku.com > Remotes > td-p Aug 28, 2020 - Solved: So I just purchased a voice remote to allow one remote for a Dynex TV in the office. I have cycled through so many brands without ... 7 answers · Top answer: All the line of sight was good. It's just that so many companies rebrand TVs that electronics ...

I have a Dynex Television. Is this compatible wit - Q&A

Best Buy https://www.bestbuy.com > site > questions > question Sep 11, 2018 - After that you need to make sure you have a wireless network so the Roku can connect. All of this takes minutes and then it will try to program ...

How To Connect Your Roku Device To Your Dynex TV

CertSimple.com https://certsimple.com > how-to-connect-your-roku-de... Nov 11, 2022 - From there, select the "Player" option and then choose the "Connect to a device" option. On the next screen, select your Dynex TV from the list ...

How to Set Up and Connect Roku to a TV: Complete Guide

wikiHow https://www.wikihow.com > Connect-Roku-to-TV 1. Connect the Roku to the TV with an HDMI cable. 2. Note the HDMI port number on the TV. 3. Turn on the Roku. 4. Turn on the TV. 5. Switch to the HDMI input on ... Videos https://www.google.com/search?q=roku+express+to+dynex+tv ..

It really depends on the model, but try this. Don't forget with analogue, you need an aerial of some type. .. https://www.google.com/search?q=Dynex+TV+Auto+Channel+setup ..