Top 20 Kyocera Mita KYOCERA/MITA - KM-C3130 Printer Questions & Answers

c4000 polygon motor sychronize error, try to cleaning polygon, if not effective, need to replace new polygon.

This is a hard disk error. When we were troubleshooting yesterday you said you were going to try and disconnect some sensors to by-pass the problem with the Image Units. Did you put them all back? This hard disk error states that it can not communicate with the built-in hard disk.

Jim
Preston Computer Services
www.prestoncomputerservice.com

try to used vacuum cleaner, 

First problem is for some reason your KMC 3130 crosses over to a Konica Minolta CF3102 and there is no C-0991 code listed for those machines. However, that C-0991 code is a common paper tray lift failure code on Konica MInolta machines.
So I would recommend opening and checking all of your paper trays to make sure nothing is binding them and that the paper is loaded properly.
Then open and close the large front door to reset the code.
If the code comes back then open all of your paper trays and LEAVE them open. Next open and close the front door to reset the code. The copier should now come to "ready to copy"
Then close each paper tray 1 at a time waiting 30 seconds between each tray closing. Once the code pops back up after closing a particular tray then you will know for sure which tray is causing the problem.
You can use the copier by leaving this tray open if need be.
Good Luck.

grab the service manual and operations guide here... it is either in the operations guide or the service manual... both are a bit complicated but its there... good luck... I’m happy to assist further over the phone at https://www.6ya.com/expert/norman_d2fa496dce30c65d

faulty memory and or faulty power board... I’m happy to assist further over the phone at https://www.6ya.com/expert/norman_d2fa496dce30c65d

mhn arahan untuk problem yang saya alami dalam pengoperasian hp officejet 7210 all in one -
problem : kedua tinta hp black print cortridge 96 dan hp color treecolor 97 uda di masukan kedalam kotak atau wadahnya, namun, perintah yang keluar adalah : remove and check color cartridge mhn arahan tks

Try with 50% alcohol.

Question edited to better English and spelling. Question moved to Kyocera MITA. https://www.google.com/search?q=Kyocera+Mita%2C+replaced+toner+but+still+says+replace+toner ..

https://www.manualslib.com/manual/359935/Kyocera-Km-2530.html?page=1#manual https://www.manualslib.com/manual/359935/Kyocera-Km-2530.html?page=10#manual https://www.manualslib.com/manual/359935/Kyocera-Km-2530.html?page=11#manual

Question edited for a lot more clarity!! Question moved to make model category. No you have to fix it. You need a service call.

KM-3050 KM-4050 KM-5050

moroinformatica.it http://www.moroinformatica.it > docs > KYOCE PDF Apr 1, 2013 - KM-4050. KM-5050 ... (4) How to tell a genuine Kyocera Mita toner container ... F14F. Power source PWB secondary side error. Defective power. 455 pages

Hi, Check the power saving setting under the printer. Usually the power saving setting for network is switched on, this needs to be switched off.

motor y sustituir la cinta de transferencia

You don't need to shake the toner. You only need to shake the toner when you install a new one. Shaking the toner to make it last later can give the copier a false toner reading.

You don't . OEM toner works best.

Press and hold the following buttons in the sequence below. (1) Stop/clear, (2) start, (3) exposure lighter, (4) exposure darker, release the 4 buttons and press the stop/clear button again. the display should now indicate 000. below the display are 3 buttons... press the left button once, the middle button 6 times, and the button on the right 3 times. the display should now indicate 163.... press the start button 3 times. your machine will now restart, and if the code was as a result of a power problem, should now work fine. if not the problem could be related to the fixing unit, power supply, or one of the boards. Also do not tamper with any settings while in the service mode, this WILL have undesired effects. TAKE NOTE, this will only work if your model is the KM-1500

press and hold the following buttons in the sequence below. (1) Stop/clear, (2) start, (3) exposure lighter, (4) exposure darker, release the 4 buttons and press the stop/clear button again. the display should now indicate 000. below the display are 3 buttons... press the left button once, the middle button 6 times, and the button on the right 3 times. the display should now indicate 163.... press the start button 3 times. your machine will now restart, and if the code was as a result of a power problem, should now work fine. if not the problem could be related to the fixing unit, power supply, or one of the boards. Also do not tamper with any settings while in the service mode, this WILL have undesired effects. TAKE NOTE, this will only work if your model is the KM-1500

http://www.koceramitaofficeequipment.com/