Kyocera Mita KM-1815 All-In-One Laser Printer - Answered Questions & Fixed issues
MITA TA180 ERROR MESSAGE C6000
Fuser heater break
Fuser thermistor 1 detected less than
70°C/158°F for 10 s during warm-up and
ready in.
During warm-up, the temperature at the
fuser unit thermistor 1 does not rise by
1°C/1.8°F continuously for 5 s.
Fuser thermistor 2 detected less than
40°C/104°F for 10 s during warm-up and
ready in.
During warm-up, the temperature at the
fuser unit thermistor 2 does not rise by
1°C/1.8°F continuously for 5 s.
Defective fuser
heater 1 or 2.
Replace the fuser heater 1 or 2.
Installation defectiveness
on fuser
thermistor 1 or 2.
Check the mounting state of the fuser thermistor
1. If any problem is found, repair it.
Defective fuser
thermostat.
Replace the fuser thermostat.
Defective PWB. Replace the power source PWB or engine
PWB and check for correct operation
12/11/2017 9:55:33 AM •
Kyocera Mita...
•
Answered
on Dec 11, 2017
•
65 views
C7980
waste toner is full,,emptying it will get rid of the code!
3/4/2014 12:09:42 PM •
Kyocera Mita...
•
Answered
on Mar 04, 2014
•
122 views
Kyocera 1815 la y sale
The error means - Abnormally high fixing unit thermistor temperature.
Can be caused by Shorted thermistor or Broken heater control circuit on the power supply board.
9/5/2012 6:28:09 AM •
Kyocera Mita...
•
Answered
on Sep 05, 2012
•
347 views
How to fix code C6020
how to fix error c6020...1st step is go get a gasoline and a match and then pour the gasoline to the kyocera and then lit it with your match stick...it will automatically restart..for more details contact your kyocera supplier.
6/21/2012 3:57:03 AM •
Kyocera Mita...
•
Answered
on Jun 21, 2012
•
871 views
How do i reset error
try holding the power button down for 10 seconds
if this helps please rate
Thanks
Robert
7/1/2011 5:18:52 AM •
Kyocera Mita...
•
Answered
on Jul 01, 2011
•
552 views
KYOCERA MK 1500
ERROR C-6
Contents: Broken fixing heater wire
• In fixing warm-up, the time to reach
50°C/122 °F exceeds 13.5 s, the time
to reach 100°C/212 °F exceeds 10 s,
the time to reach the primary stabilization
exceeds 10 s or the time to
reach the secondary stabilization exceeds
24 s.
Causes: Poor contact in the thermistor connector terminals.
Check procedures/corrective measures: Check the connection of connector CN4 on
the power supply board (KP-5059) and the
continuity across the connector terminals.
Repair or replace if necessary.
Causes: Thermistor installed incorrectly.
Check procedures/corrective measures: Check and reinstall if necessary.
Causes: Thermal cutout triggered.
Check procedures/corrective measures: Check for continuity. If none, replace the
thermal cutout.
Causes: Heater lamp installed incorrectly.
Check procedures/corrective measures: Check and reinstall if necessary.
Causes: Broken heater lamp wire.
Check procedures/corrective measures: Check for continuity. If none, replace the
heater lamp.
2/21/2011 5:43:40 PM •
Kyocera Mita...
•
Answered
on Feb 21, 2011
•
514 views
APARECE EL CODIGO C6020 Y
El codigo C6020 significa que hubo sobrecalentamiento en el Fuser. Si Ud. es tecnico en copiadoras, cheque la resistencia del THMS, ien caso de ser 0 ohms, reemplace. De otro modo, puede que la fuente de poder esté dañada. despues de hacer reemplazo de piezas, resetee la copiadora con el codigo U163.
En caso de no tener idea de que estoy hablando, le recomiendo solicitar servicio tecnico para la computadora ya que es un problema serio en el equipo.
2/12/2014 4:45:33 AM •
Kyocera Mita...
•
Answered
on Feb 12, 2014
•
984 views
My kyocera printer km 1820
cheap kyocera mita copier repair and parts installation just txt or call 09194851549, 09168932315
also offering free estimate within metro manila (ncr) philippines any kyocera mita brand we can fix it!!!
12/5/2010 6:04:04 AM •
Kyocera Mita...
•
Answered
on Dec 05, 2010
•
521 views
Kyocera c3200 error Problem
A C3200 is as follows:
Exposure Lamp Problem.
• In indicator check before starting copying, the average value in scanning of the shading plate with the CCD is 128 or more.
Solution:
Defective scanner board (KP-5063).
Replace the scanner board (KP-5063) and check for correct operation
Defective exposure lamp or inverter board.
Replace the exposure lamp or inverter board.
Incorrect shading position.
Adjust the position of the contact glass (shading plate). If the problem still occurs, replace the scanner home position sensor.
Poor contact of the connector terminals.
Check the connection of connector YC7 on the scanner board (KP-5063), and the continuity across the connector terminals. Repair or replace if necessary.
These are direct from the Tech man.
More than likely it is the Exposure Lamp.
Hope this helps.
8/24/2010 4:48:56 AM •
Kyocera Mita...
•
Answered
on Aug 24, 2010
•
6,021 views
How to intall printer
first insert the cd which comes with the printer n follow the instruction, when it tell you to connect the printer then only you connect n follow the instruction
8/16/2010 10:09:32 AM •
Kyocera Mita...
•
Answered
on Aug 16, 2010
•
53 views
Not finding what you are looking for?