20 Most Recent Kyocera Mita KM-5035 Printer - Page 5 Questions & Answers


Hello sir; Just follow my instruction, I will help you to get rid off the error code; With front door open press10871087 then enter 163 press "start" key, final press " stop/clear " key to get out reset procedure.

Kyocera Mita... | Answered on Jul 19, 2018


Developing unit connector insertion
problem
Absence of the developing unit is
detected.
Developing unit
connector inserted
incorrectly.
Reinsert the developing unit connector if
necessary.
Defective developing
unit connector.
Replace the developing unit.

Kyocera Mita... | Answered on Dec 11, 2017


Polygon motor synchronization problem
The polygon motor does not reach the
stable speed within 20 s of the START
signal turning on.

Check the connection of connector YC3 on
the engine PWB and laser scanner unit, and
the continuity across the connector terminals.
Repair or replace if necessary.
Defective polygon
motor.
Replace the laser scanner unit.
Defective engine
PWB.
Replace the engine PWB and check for correct
operation.

Kyocera Mita... | Answered on Dec 11, 2017


Its either the lift motor problem or the engine board

Kyocera Mita... | Answered on Dec 11, 2017


Exposure lamp problem
When input value at the time of exposure
lamp illumination does not exceed the
threshold value between 5 s.

Check the connection of connector YC5 on
the ISM PWB and the connector on the
inverter PWB, and the continuity across the
connector terminals. Repair or replace if
necessary.
Defective exposure
lamp or inverter
PWB.
Replace the exposure lamp or inverter
PWB.
Incorrect shading
position.
Adjust the position of the contact glass
(shading plate). If the problem still occurs,
replace the home position switch.
Defective PWB. Replace the ISM PWB, ISC PWB or CCD
PWB and check for correct operation.

Kyocera Mita... | Answered on Dec 11, 2017


fuser related problem press 1087*2 then 163 and start click start en execute

Kyocera Mita... | Answered on Dec 11, 2017


Hi,
Your machine have a fuser Unit problem. Usually on the older models the fuse needs to be replaced or reset.

Kyocera Mita... | Answered on Nov 09, 2017


Hi,
The toner container could be locked. Remove toner container and shake well. Switch machine off and back on again.
Hope this helps.

Kyocera Mita... | Answered on Nov 09, 2017


Hi, Check the power saving setting under the printer. Usually the power saving setting for network is switched on, this needs to be switched off.

Kyocera Mita... | Answered on Nov 09, 2017


Needs firmware update

I’m happy to help further over the phone at https://www.6ya.com/expert/mustafa_06f84c65ab5cc745

Kyocera Mita... | Answered on Jul 23, 2017


??????????

Kyocera Mita... | Answered on Jul 23, 2017


On most Kyocera Mita copiers a J-11 code indicates a possible paper jam when paper is being fed from drawer #1, but sometimes a J-11 will be indicated when the paper fails to feed from the drawer. Check the paper stops and paper guides in the drawer and make sure that they are flush against the paper, also cleaning the paper feed and pick-up rollers with a rag dampened with just plain water will help sometimes unless the rollers are completely worn out. If all this doesn't help you may have a paper feed clutch or lift motor that has failed.

Kyocera Mita... | Answered on Jul 10, 2017


replace the driver and check the files your sending one or the other is corrupt.

Kyocera Mita... | Answered on Jun 22, 2017


reset fuser error in service mode ,simulation 163,

Kyocera Mita... | Answered on Apr 29, 2017


You don't . OEM toner works best.

Kyocera Mita... | Answered on Sep 29, 2016


You don't need to shake the toner. You only need to shake the toner when you install a new one. Shaking the toner to make it last later can give the copier a false toner reading.

Kyocera Mita... | Answered on Sep 29, 2016

Not finding what you are looking for?
Kyocera Mita KM-5035 Printer Logo

115 questions posted

Ask a Question

Usually answered in minutes!

Top Kyocera Mita Office Equipment & Supplies Experts

Adorjani Laszlo

Level 3 Expert

1316 Answers

AAAA262430

Level 2 Expert

51 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Kyocera Mita Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kyocera Mita Office Equipment & Supplies

  • Kyocera Mita Office Equipment & Supplies

Most Popular Question

replacing dc controller board

  • Office Equipment & Supplies
Loading...