Top 20 Kyocera Mita KM-5035 Printer Questions & Answers


there are many reasons for this .first make sure you installed the toner container very well. second type 1087 twice to service menue then type 30 to chick motors then exit and type 130 to adjust toner mode when the machine stop turne it off-on

Kyocera Mita... | 87 views | 0 helpful votes


my dear selct ip adress

Kyocera Mita... | 500 views | 0 helpful votes


reset fuser error , via service mode

Kyocera Mita... | 148 views | 0 helpful votes


Hi,

When replacing DC/main PWB or engine board, be sure to remove the EEPROM from DC, main PWB or engine board that has been removed and then re-attach it to the new DC/main PWB or Engine PWB, cheers

Kyocera Mita... | 183 views | 1 helpful votes


This code means that there is a problem with the fuser unit

Kyocera Mita... | 76 views | 0 helpful votes


press10871087 after press163 reast

Kyocera Mita... | 387 views | 0 helpful votes


waste toner motor error, under cover on right side of machine, will have to be replaced. also motor could of damaged PWB.

Kyocera Mita... | 73 views | 0 helpful votes


Go through the maintenance procedures in your manual. All cleaning should be done which probably includes roller cleaning but you should run it through all the procedures.

Kyocera Mita... | 102 views | 0 helpful votes


drum or development unit need replacing!!

Kyocera Mita... | 34 views | 0 helpful votes


Could be the paper full tab is "stuck up" at the exit, or at least unplug the finisher from the unit and cycle power, pull away and see if it prints. -Carl

Kyocera Mita... | 44 views | 0 helpful votes


Main charger problem

Kyocera Mita... | 38 views | 0 helpful votes


Take to dealer..

Kyocera Mita... | 27 views | 0 helpful votes


Default is admin admin.

Kyocera Mita... | 133 views | 0 helpful votes


Image formation unit.
Has the drum been removed from this machine.Its either missing or requires replacing

Kyocera Mita... | 93 views | 0 helpful votes


What error code?

Kyocera Mita... | 37 views | 0 helpful votes


This code indicates that the fuser unit has failed.
Please consult with your local dealer.

Kyocera Mita... | 43 views | 0 helpful votes


Ensure that you are using the correct driver,
Ensure that you have set auto configure in the driver device settings or tick the relevant box's.

Kyocera Mita... | 61 views | 0 helpful votes


press 1087 1087 reset 20

Kyocera Mita... | 29 views | 0 helpful votes


Indicates that you may not have the cable from the back of the document feeder plugged in correctly.
Please ensure that you have turned the copier off before you unplug and re plug in this connector

Kyocera Mita... | 71 views | 2 helpful votes

Not finding what you are looking for?
Kyocera Mita KM-5035 Printer Logo

115 questions posted

Ask a Question

Usually answered in minutes!

Top Kyocera Mita Office Equipment & Supplies Experts

Adorjani Laszlo

Level 3 Expert

1316 Answers

AAAA262430

Level 2 Expert

51 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Kyocera Mita Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kyocera Mita Office Equipment & Supplies

  • Kyocera Mita Office Equipment & Supplies

Most Popular Question

replacing dc controller board

  • Office Equipment & Supplies
Loading...