Juki MO6714 Mechanical Sewing Machine - Answered Questions & Fixed issues
Bartack machines skipping
Hello Keith, From the little information you stated, I can only take a stab at what might be wrong with your machine. I suggest you make sure the take up spring is working freely and properly.
3/27/2014 4:03:28 AM •
Juki MO6714...
•
Answered
on Mar 27, 2014
•
56 views
Juki skipping stitches
completely un-thread the machine and rethread it in this order. Upper Looper, Lower looper, right needle Left needle. It has to be in that order ALWAYS. If you break a thread... un thread and start the threading process again. If rethreading doesn't work... change the needle that is skipping. Good luck
8/16/2012 3:46:22 AM •
Juki MO6714...
•
Answered
on Aug 16, 2012
•
1,604 views
I change the news blade
hi there,
which blade you change? upper or lower one?
for lower one just make the top surface for blade aqual with throat plat.
for upper lower turn handwheel to make blade at lowest position in that time the upper lower must be lower than lower blade by arround 2.5mm and keep in your main the two blade also must be very close no space between it.
best regards
ashraf abozid
[email protected]
CAIRO - EGYPT
8/26/2011 1:51:34 AM •
Juki MO6714...
•
Answered
on Aug 26, 2011
•
486 views
Question about Juki Overlock MO-6704
Someone
Hi, yes I believe that will work, however you may need to re-adjust several time to get it perfect, my wife ( who's owned a couple industrial machines agrees ) use some scrap material to make adjustments and if possible ( with machine unplugged of course ) turn by hand to make sure it is not too far and could jam. I hope this was useful, please write back to let me know-even if not so we may try to help some more. Thanks for asking FixYa, and good luck-Prodzilla
4/26/2011 5:05:57 PM •
Juki MO6714...
•
Answered
on Apr 26, 2011
•
179 views
I have a JUKI HZL - DX7. There is a problem with the automatic thread cutter.
If your JUKI HZL-DX7 sewing machine's automatic thread cutter is leaving behind a short piece of thread in the mechanism after each cut, there might be a few potential causes for this issue. Here are some steps you can take to troubleshoot and address the problem:
- Thread Tension: Check the tension settings for both the upper and lower threads. Improper tension can cause thread to be left behind in the thread cutter mechanism. Make sure the tension is balanced and appropriate for the type of fabric you're sewing.
- Thread Quality: Poor-quality or thick threads can sometimes get caught in the thread cutter mechanism. Ensure you're using good-quality threads that are suitable for your sewing project.
- Thread Path and Thread Guides: Make sure the upper and lower threads are properly threaded through the machine's threading path and guides. Improper threading can lead to thread buildup in the cutter area.
- Thread Cutter Mechanism Cleaning: The thread cutter mechanism might have accumulated lint, debris, or bits of thread over time. Gently clean the thread cutter area with a small brush, compressed air, or a vacuum cleaner to remove any buildup.
- Blade Inspection: Check the blade of the thread cutter for any nicks, dullness, or damage. A damaged blade might not cut the thread cleanly, leaving behind remnants.
- Thread Cutter Mechanism Lubrication: Some sewing machines have small moving parts in the thread cutter area that benefit from occasional lubrication. Consult your sewing machine's manual to see if lubrication is recommended and use a sewing machine-safe lubricant if needed.
- Machine Maintenance: Regular maintenance of your sewing machine, including cleaning and oiling as recommended in the manual, can help prevent issues with the thread cutter mechanism.
- Consult the Manual: Refer to your JUKI HZL-DX7 sewing machine's manual for specific instructions on troubleshooting and maintaining the automatic thread cutter.
- Professional Service: If the issue persists after trying these steps, it might be best to seek the assistance of a professional sewing machine technician. They can diagnose and repair any mechanical issues with the thread cutter mechanism.
Remember that working with sewing machines involves mechanical parts and electrical components, so it's important to follow safety guidelines and, if needed, seek professional assistance to avoid causing further damage or harm.
8/5/2023 10:34:15 AM •
Juki Sewing...
•
Answered
on Aug 05, 2023
•
112 views
My machine is a Juki HZL-F600 Quilt & Pro Special.
When experiencing a sewing machine jam and encountering an error message like "lower pressure foot" on the Juki HZL-F600 Quilt & Pro Special, it indicates there may be an issue with the machine's threading, bobbin, or pressure foot. Here are some steps you can take to troubleshoot and resolve the problem:
- Rethread the Machine: Start by completely rethreading both the top thread and bobbin thread. Ensure that the threads are properly seated in the tension disks, thread guides, and the bobbin case. Follow the threading instructions in the machine's user manual to ensure correct threading.
- Check the Bobbin: Remove the bobbin and inspect it for any tangles, knots, or thread buildup. Clean out any lint or debris in the bobbin area. Make sure the bobbin is wound correctly and placed in the bobbin case with the thread feeding in the correct direction.
- Verify the Pressure Foot: Double-check that the pressure foot is properly attached and lowered. Ensure that it is securely in place and there are no obstructions preventing it from making proper contact with the fabric.
- Adjust Thread Tension: Incorrect thread tension can also cause sewing issues. Experiment with adjusting the tension settings on the machine to find the optimal balance for your fabric and thread. Refer to the machine's user manual for guidance on adjusting thread tension.
- Clean and Lubricate: Regularly clean and lubricate your sewing machine to ensure smooth operation. Follow the manufacturer's instructions for cleaning and lubrication, and pay special attention to the bobbin area and the needle area.
- Seek Professional Assistance: If the issue persists after attempting the above steps, it is recommended to contact a qualified technician or the Juki customer support for further assistance. They can provide specialized guidance and troubleshooting specific to your Juki HZL-F600 Quilt & Pro Special machine.
Remember to always consult the machine's user manual for specific instructions and guidance. If you're uncertain or uncomfortable performing any troubleshooting steps, it's best to seek professional help to avoid potential damage to the machine.
7/15/2023 1:56:18 PM •
Juki Sewing...
•
Answered
on Jul 15, 2023
•
71 views
Not finding what you are looking for?