20 Most Recent Reebok RX 1000 TREADMILL Drive Motor - Page 3 Questions & Answers

i too have this problem am under the impression there is a problem with the resistance but am waiting on areply from reebok technical support

Loosen, but do not completely remove the idler bolts (on the back where you get on). Remove the side rail and motor hood (left side usually). While turning the drive roller by hand, pull on the inside of the belt in order to walk it off of the drive roller pully. Remove the belt and put the new one in.

Check the low voltage supply, that is what supplies the 'brain' and display.

You failed to mention your question.

Contact Reebok directly to request the schematic diagram.

Error code E05 indicates a problem with the belt speed. Unlikely it is a bad sensor given the smell and heat. Hopefully it is under warranty. There are troubleshooting tips is the user guide. Here is an assembly model that serves for both the ZR8 and ZR9. The following indicates how to adjust speed and lubricatrThe first one may help narrow down the problem but the others may prove more helpful. If adjustment does not help, you likely will have to try a service tech. https://anytreadmillparts.com/pages/treadmill-error-code-troubleshooting https://www.sportsrec.com/351318-how-to-troubleshoot-my-reebok-treadmill.html https://www.manualslib.com/manual/1064934/Reebok-Z9.html https://www.youtube.com/watch?v=OFn0aVzkFlE

Request the wiring diagram from Reebok.

Contact Reebok directly to request the diagram.

Loose or broken parts under the motor hood of your treadmill can cause the machine to not start. If the console lights up, but the treadmill won't start, the motor controller could be damaged. Loose wires under the motor hood or in the console can cause your treadmill not to start.

This is a tedious process. Leave one of the adjusters where it is and adjust the other side until the belt starts to move to the center. This has to be done with the treadmill moving the belt so that the belt can move into position. Once the belt is in a central position, then you turn the adjustment screws one half of a turn on each one until the belt is tight enough.

If you wish get some details about treadmill repair check the link below www.electro-medical.blogspot.com

check and test safety [kill ] switch- circuit - motor

Simply stretch it onto the top of the smaller drive and rotate the motor to secure it on fully!

https://www.sportsrec.com/351318-how-to-troubleshoot-my-reebok-treadmill.html If the electrical outlet works, unplug the treadmill and check the power cord for damage. Replace the power cord if it's damaged. If the power cord is okay, check the circuit breaker switch on the treadmill and reset the circuit breaker switch if it's tripped. https://www.searspartsdirect.com/diy/symptom/treadmill-repair/1234711/won-t-power-up/tm520420

Hi, it may be stuck, try and force move the belt safely. if it moves turn it on again and try to start it, Be sure it has power and using the correct cables, make sure the security key is in it, make sure its setup properly without obstruction. Good Luck Mr.Mike

https://www.youtube.com/watch?v=VUSvc2A5gIY

https://www.youtube.com/watch?v=Ygldc8mI7Rw https://www.youtube.com/watch?v=Y6RJSCWt2G0

https://www.youtube.com/watch?v=XyPedy7HtzM

https://www.youtube.com/watch?v=a2FCo3JTO00 E02 error code: control board or motor issue. Test the motor first to check if the motor can runing normally. If motor is normal, replace the control board. E03 error code: 1,Turn on the treadmill , motor running a few seconds then stop and console board shows E03, probably the Speed sensor issue. https://anytreadmillparts.com/pages/treadmill-error-code-troubleshooting

is this a tread mill?> what does the power pack say. on side. ? it should show this. wrong pack?