Reebok 8000 ES Treadmill - Page 3 - Answered Questions & Fixed issues

0helpful
1answer
0helpful
2answers

How do I oil my Reebok i-run treadmill?

I have a problem with my reebok i walk i run treadmill. The belt does not move on the lower speeds and after using it there is a burning smell even though it is working fine once I get past the first two speeds. I have had it 2 years but have never oiled it as I am not sure how and where.
7/5/2021 7:16:42 AM • Reebok Exercise... • Answered on Jul 05, 2021 • 5,662 views
0helpful
1answer

GT40s treadmill. Why doesn't it turn on?

Your treadmill may not be turning on due to a broken or a failed power supply or a broken power cord or a tripped circuit breaker switch a failed circuit breaker switch a bad power switch or wiring failure or a bad motor control board or failed console display screen can stop the treadmill from turning on. If the outlet is not working try to reset the house circuit breaker which is located inside of the fuse box to restore power to the outlet.
5/1/2021 2:46:47 AM • Reebok Exercise... • Answered on May 01, 2021 • 3,195 views
0helpful
1answer

GT40s treadmill. how can I replace the driver belt?

Loosen, but do not completely remove the idler bolts (on the back where you get on). Remove the side rail and motor hood (left side usually). While turning the drive roller by hand, pull on the inside of the belt in order to walk it off of the drive roller pully. Remove the belt and put the new one in.
2/19/2021 2:42:54 PM • Reebok Exercise... • Answered on Feb 19, 2021 • 413 views
0helpful
1answer

Model GT60 treadmill. What does it mean when it stops and displays error E05?

E01 error code: communication failure: console board and control board cannot communicate.probably console board issue or control board issue or data cable issue. replace a data cable,checking whether the machine can running? If no, Replace the control board.
4/6/2022 10:10:59 AM • Reebok Exercise... • Answered on Apr 06, 2022 • 463 views
0helpful
1answer

9500 ES, model RBTL14506.4 treadmill. Why doesn't magnet key work?

Contact Reebok directly to request the schematic diagram.
1/11/2021 3:47:16 PM • Reebok Exercise... • Answered on Jan 11, 2021 • 77 views
0helpful
2answers

Model RBTL09104 treadmill. Where can I get a wiring diagram?

Request the wiring diagram from Reebok.
1/4/2021 5:56:07 PM • Reebok Exercise... • Answered on Jan 04, 2021 • 197 views
0helpful
1answer

Model ZR8. Not working. What do error codes E03 and E05 mean?

Error code E05 indicates a problem with the belt speed. Unlikely it is a bad sensor given the smell and heat. Hopefully it is under warranty. There are troubleshooting tips is the user guide. Here is an assembly model that serves for both the ZR8 and ZR9. The following indicates how to adjust speed and lubricatrThe first one may help narrow down the problem but the others may prove more helpful. If adjustment does not help, you likely will have to try a service tech. https://anytreadmillparts.com/pages/treadmill-error-code-troubleshooting https://www.sportsrec.com/351318-how-to-troubleshoot-my-reebok-treadmill.html https://www.manualslib.com/manual/1064934/Reebok-Z9.html https://www.youtube.com/watch?v=OFn0aVzkFlE
1/7/2021 3:53:26 PM • Reebok Exercise... • Answered on Jan 07, 2021 • 1,174 views
0helpful
1answer

Edge 2.2 RE0M-11301BKWH. Where can I get the wiring diagram?

Contact Reebok directly to request the diagram.
1/4/2021 3:27:55 PM • Reebok Exercise... • Answered on Jan 04, 2021 • 199 views
0helpful
1answer

Model 5500C. Why doesn't it start?

Loose or broken parts under the motor hood of your treadmill can cause the machine to not start. If the console lights up, but the treadmill won't start, the motor controller could be damaged. Loose wires under the motor hood or in the console can cause your treadmill not to start.
12/1/2020 9:51:51 AM • Reebok Exercise... • Answered on Dec 01, 2020 • 122 views
0helpful
3answers

I have a reebok I run the belt was slipping when I was running without incline I removed the bolts at the end so I could grease the belt now I cant get the belt central again please help have I done something wrong removing the bold that tighten the belt? Thanks

This is a tedious process. Leave one of the adjusters where it is and adjust the other side until the belt starts to move to the center. This has to be done with the treadmill moving the belt so that the belt can move into position. Once the belt is in a central position, then you turn the adjustment screws one half of a turn on each one until the belt is tight enough.
11/28/2020 2:29:35 AM • Reebok Exercise... • Answered on Nov 28, 2020 • 2,133 views
0helpful
2answers

Incline not working on Reebok ZR9

If you wish get some details about treadmill repair check the link below www.electro-medical.blogspot.com
10/27/2020 9:57:59 AM • Reebok Exercise... • Answered on Oct 27, 2020 • 1,947 views
0helpful
2answers

Treadmill Reebok ZR9 When machine is switched on display flashes and makes a beeping noise

Rebock zr9 treadmill is working but cant see the screen
7_27_2020_5_27_11_pm.jpg
4/23/2022 3:48:50 PM • Reebok Exercise... • Answered on Apr 23, 2022 • 2,882 views
0helpful
1answer

I have a reebok treadmill, the motor belt is off how do I put it back on pls

Simply stretch it onto the top of the smaller drive and rotate the motor to secure it on fully!
6/6/2020 6:51:18 PM • Reebok Exercise... • Answered on Jun 06, 2020 • 458 views
0helpful
1answer

Reebok gt60 treadmill won't run, but has power.

https://www.sportsrec.com/351318-how-to-troubleshoot-my-reebok-treadmill.html If the electrical outlet works, unplug the treadmill and check the power cord for damage. Replace the power cord if it's damaged. If the power cord is okay, check the circuit breaker switch on the treadmill and reset the circuit breaker switch if it's tripped. https://www.searspartsdirect.com/diy/symptom/treadmill-repair/1234711/won-t-power-up/tm520420
5/30/2020 4:48:52 PM • Reebok Exercise... • Answered on May 30, 2020 • 910 views
0helpful
1answer

I have a treadmill - Reebok GT40S. I haven't used it for 4 mths. Have just switch it on and the dial is blank, but is bleeping. Nothing is moving. What can I do.

Hi, it may be stuck, try and force move the belt safely. if it moves turn it on again and try to start it, Be sure it has power and using the correct cables, make sure the security key is in it, make sure its setup properly without obstruction. Good Luck Mr.Mike
5/21/2020 1:15:28 AM • Reebok Exercise... • Answered on May 21, 2020 • 886 views
0helpful
1answer

How can i fix code U5 in reebok TR2 premier run treadmill

https://www.youtube.com/watch?v=VUSvc2A5gIY
4/26/2020 10:06:18 AM • Reebok Exercise... • Answered on Apr 26, 2020 • 168 views
Not finding what you are looking for?
Reebok 8000 ES Treadmill Logo

30 questions posted

Ask a Question

Usually answered in minutes!

Top Reebok Exercise & Fitness Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Paul Carew

Level 3 Expert

3808 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Reebok Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...