Reebok Acd1 Treadmill Motor Control Board 141877 - Answered Questions & Fixed issues
I have a reebok pro
hi,
You can find the board in side the teradmill near the motor . There will be some wire in the old board you have to pull out those wires from that board one by one and connect it to the New board. After that remove the screw from the old board and place the new board there.
I have added a video which demonstrate how to replace the motor control board of a treadmill. will help you to do the same.
ok
8/5/2011 6:33:09 AM •
Reebok Acd1...
•
Answered
on Aug 05, 2011
•
328 views
I have a reebok edge
I had this very same problem. I sorted it out this way: the information that Argos supplies says the speed starts at 0.8 kph with a top speed of 14 kph. If your Reebok Edge starts at a speed of 0.5 and has a top speed of 8.8, then the speed and distance is measured in mph, rather than kph. You can check this yourself with the following online speed converter:
http://www.eforecourt.com/mph_kph_speed_convert.htm
11/3/2011 1:55:52 PM •
Reebok Acd1...
•
Answered
on Nov 03, 2011
•
2,004 views
The treadmill will sometimes start and most times
Hello,
With the motor cover off and the power on, make sure there is a red light/led lit on the controler, if yes then press the start button then press #3 on the speed side. If not lit, you dont have power to the controller. If you had a red light, and pressed the speed button, the light should start flashing just before the walk belt starts to move. If the speed button is pushed and the light on the controller does not flash, you have a problem in the console. This is only fixed by replaceing the controler.
Sorry.
Hope this was at least helpfull, Matt If you need further help, I’m available over the phone at
https://www.6ya.com/expert/matt_8dbc24bf722649ac
12/31/2010 3:59:57 AM •
Reebok Acd1...
•
Answered
on Dec 31, 2010
•
868 views
I paused the treadmill to answer the phone, and
If you have the expertise to replace individual components, it's easy to repair, and inexpensive.
Replace DZ1 and DZ4, found under the 2 grey resistors. DZ1 is a 15v, 1watt zener diode, zd4 is a 24v 5 watt zener diode. The copper print may be damaged by the heat, so it will need to be repaired as well.
Also, the discolored resistor (R57) may also need to be replaced. It is a 1K ohm 2 watt resistor, replace it with a 1K ohm 5 watt resistor.
If you are unable to replace the components and do the repair, the motor controller is easy to find online and replace yourself.
One of the most common reasons why these boards fail prematurely, is because people do not turn the machine off when done using. Removing the safety key does not turn the machine off, only the console!! Turn it off by the on/off switch or unplug it after use.. I have replaced numerous controllers that failed when the machine was not even being used at all..
1/8/2024 6:54:44 AM •
Reebok Acd1...
•
Answered
on Jan 08, 2024
•
1,576 views
UNIT DOES NOT POWER UP. I CHANGED THE POWER BOARD
If its a Icon Health and Fitness branded treadmill (proform,image ,healthrider etc.)The safety key activates the on off switch for the console. (micro switch activated by safety key)Check for 9-12v going to console. Unless it has a magnet switch. What brand and model ?
9/16/2010 7:28:07 PM •
Reebok Acd1...
•
Answered
on Sep 16, 2010
•
617 views
Treadmill will not start. i replaced power board.
Hello,
Check
your wiring and check your ground. If all that checks out then triple
check your control board. Also the motor should have a reset button make
sure that the button is not out and it is fully pushed in.
Take care.
9/14/2010 2:43:20 AM •
Reebok Acd1...
•
Answered
on Sep 14, 2010
•
315 views
REEBOK GT30 TREADMILL. It has ERROR E2. What does this mean please?
E2 Error usually indicates that the treadmill is overloaded and applies to various models like TR150, TRX1000 and TR 200. To fix this problem, check if your treadmill motor is overheating. Signs of an overheated motor include; grinding noise, motor produces a burning smell and inconsistent operation speeds.
Reddit · r/fixit
3 comments · 4 years ago
Hi i have a reebok one gt30 treadmill bought in 2016. Recently at ... Start googling error codes and find out what E2 means. Upvote 2
Which part of my broken treadmill should I try replacing? - Reddit
Apr 18, 2020
Urevo 2-in-1 giving e10 error message- did you encounter this ...
Oct 10, 2022
Need help with Sole F63 treadmill error code - Reddit
Nov 21, 2022
More results from www.reddit.com
Reebok jet 300 treadmill e02 error - motor output dc is 11v on ...
All About Circuits
https://forum.allaboutcircuits.com > threads > reebok-j...
Jan 9, 2023 - It seems to me to be a problem in the circuit that gives feedback to the processor about the voltage in the motor, error02 and does not arm the ...
Missing: GT30 ' Show results with:
GT30
Treadmill Support - Reebok Fitness
reebokfitness.info
https://www.reebokfitness.info > treadmill-support
View user manuals, assembly guides, instruction books, and technical support videos for all Reebok treadmills, including how to reduce static shock.
..
Reebok treadmill e13 error message
f the E13 error code is still showing after restarting your treadmill, check to ensure that the wiring between the AC motor drive and motor cables is securely connected. If any of the cables/connectors appear loose, completely power off and unplug the treadmill before unplugging and reattaching the cables.
Reebok 8000ES stuck incline position will not decline.
https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&cad=rja&uact=8&ved=2ahUKEwj79pDHxZSCAxV_AHkGHbhiDxkQFnoECBsQAQ&url=https%3A%2F%2Fwww.justanswer.com%2Ffitness-equipment%2Fgdah0-reebok-8000es-treadmill-incline-keeps-going.html&usg=AOvVaw0mEH-BLg44uwLpy6jJGb3K&opi=89978449
Reebok GTS40 treadmill not working
Hi Chris,Hope so you're doing well, fact that it runs briefly and then flips the fuse suggests a potential overload or short circuit problem. To troubleshoot the issue, start by checking the power source and ensuring that the circuit breaker or fuse can handle the treadmill's electrical load.Inspect the power cord for any signs of damage, fraying, or loose connections. Make sure it is securely plugged into the outlet. Additionally, examine the motor control board for any visible signs of damage, such as burnt components or loose wires.Testing the motor by disconnecting the power and manually rotating the treadmill belt can help identify any obstructions or issues with the motor or belt tension. If you are unable to identify or resolve the problem on your own then download now user guide, it is advisable to consult a qualified technician or contact the manufacturer's customer support for further assistance.Hope so this will help you!Regards,Bryce JuneCEO & Founder of https://trafficriderapp.com/
Reebok ONE GT40s incline working intermittently
It sounds like there may be an issue with the incline motor or the lifting mechanism. Here are a few troubleshooting steps you can take:
- Check for any visible damage or obstructions in the incline mechanism. Make sure that there is nothing blocking the movement of the incline motor or lifting mechanism.
- Check the wiring and connections for the incline motor. Make sure that all wires are connected securely and that there are no loose or damaged wires.
- Test the voltage going to the incline motor. Use a multimeter to check that the motor is receiving the correct voltage.
- Try to manually adjust the incline. This will help you determine if the issue is with the motor or the lifting mechanism. To do this, unplug the treadmill and remove the motor cover. Locate the incline motor and manually turn the screw with an Allen wrench to raise or lower the incline. If the incline moves smoothly and easily, the issue is likely with the motor. If the incline is difficult to move or doesn't move at all, the issue is likely with the lifting mechanism.
If you're not comfortable performing these steps, it may be best to contact a professional to diagnose and repair the issue.
My Reebok 9500 ES Treadmill is stuck at it's max incline.
- Check the belt: Make sure the belt is properly aligned and tensioned, as a misaligned or loose belt could cause the incline to get stuck.
- Check the incline motor: If the incline motor is not functioning properly, it could be preventing the incline from moving. You may need to have the motor inspected or replaced.
- Check the incline sensors: If the incline sensors are not functioning properly, they could be preventing the incline from moving. You may need to have the sensors inspected or replaced.
- Check the control board: If the control board is not functioning properly, it could be preventing the incline from moving. You may need to have the control board inspected or replaced.
If these steps do no
Not finding what you are looking for?