Top 20 Tally Dot Matrix T2265C Printer Questions & Answers

The hardware alarm indicated 00002 is indicating a problem with print head movement. More specifically the error is indicating an error when the Carriage Motor has accelerated.This error can be indicated if there is any thing which may be preventing print head movement, things you can check include;The printer ribbon is not jammed and is located correctly in the printer, You can also check to ensure there is no paper jam of loose paper which may prevent print head movement,You can also check the carriage shaft to ensure it is free from paper dust or any other obstructions.With the printer powered off, the print head should slide freely across the width of the printer, you can then see if there is any obstruction to the print head.Clean the carriage shaft, and ensure it is free from any form of lubricant.Clean the timing strip and ensure it is correctly in place.

When trying to print on continuous stationery, the display may show "Online Single Load". This will occur if the printer is expecting to print on single sheet paper even though you may want it to print on continuous paper. To clear the error follow this procedure. • Take the printer off-line by pressing the Online key • Press the Setup key • Press the key under "Paperway" in the display • Select Tractor 1 (or Tractor 2 if fitted/required) • Press the key under "Set" • If the job still refuses to print try loading the printer with a single sheet of paper to clear the command. To do this remove the tractor feed paper and close the cover on top of the tractors but not the outside cover. You will see a guide into which put a single sheet of paper and press the key under "Load" in the display. • The printer should commence printing. If it does not, then press and hold the key under "LF/FF" to eject the single sheet. Now follow the instructions above again to select the Tractor. The display should read "OnLine Tractor Load". Load the tractor fed paper into the Tractors and press the key under "Load". The printer should now be ready to print. Check your software settings for the correct paper path type. Ensure that the display does not show "Manual" otherwise you will have to clear this error in the same manner as you have for Single sheet

aga error

Has something to do with the Automatic Gap Adjustment. Owner's manual says:

For more detailed information, refer to the Reference Manual on the Online CD-ROM, which I do not have (I only have the owner's manual).

You may have to talk with tech support at 800-774-2248. This will be Printronix (bought Genicom and Tally).

clean the carriage film " dust "

either your aga motor is bad or your board set is bad. Turn unit on watch the printhead while opening the cover. The printhead should move back and display "cover open". When you close cover the printhead should move closer to paper. If not bad aga motor or bad board set.

Hai this is a poblem because one of ur system file has been corrupted are deleted unfortunately so that u have to reinstall the os to work on the system.

I am already faced this problem, This Problem is due to Bad Head cable. Repaced that cable, your Problem will be resolved

check line in is not broken look at the socket

https://www.manualslib.com/manual/564991/Tallygenicom-6300-Series.html?page=80 TallyGenicom 6300 Series Maintenance Manual Platen Calibration Option...

Hi Sheila. I've never owned a Tally, but here are some generic speed-up tips, based on my Samsung M/F, so your menu may be different. Activate: Eco-mode or economy mode. Draft mode. Choose 'speed' over 'quality'. Mono rather than color (for documents). These steps both speed up PPM and save toner/ink. Regards, Clive.

answer in your last post

it may be due to incomplete installation as well as may be some files are deleted or removed

The Printhead is not where the printer expects it to be. Usually the carriage is jammed, which can be caused by a faulty ribbon. If the carriage is not moving freely with the printer off try to find what is causing the bind.

Does your user name and password have administrative rights on the computer? If not then you may need try with a user that does. I have run into some software that will throw a similar error if the folder already exists.

This is posted in Printers and faxed I'd suggest moving it to a software support forum.

This is a printer forum I'd recommend posting this in the correct category.

Set it to Epson Emulation and use the Epson LQ-1070 driver.

Here is the part.

This applies to Tally 7.2 and above. 1. You can export only registers and not masters 2. In any view register mode the export / import option becomes availble. 3. Click export. 4. Tally prompts you for a file name. The default name is always Tally.txt. 5. Pl rename the file to represent the ledger you are exporting else Tally will over write an existing file. 6. Tally will always save the file in the same drive / folder where Tally data resides. You cannot change this. 7. The file saved is the CSV file. 8. Open this file with Excel and map the fields.