Behringer XENYX 2442FX Mixer - Page 9 - Answered Questions & Fixed issues


Radio Shack may have the fans or can order it for you take the fan to a local Radio Shack store.

Behringer Music | Answered on Oct 20, 2015 | 89 views


In my opinion, due to the physical appearance of pmp4000 and pmp3000 look the same, it will most likely also have a common circuit and parts list (at least, most).
Usually Behringer (and all the manufacturers), with the same series / sequence, using the same circuit, the difference is the number of channels only. You can compare the parts list on PMP3000 schematic, with your PMP4000.
PMP4000.
ziro-need-part-list-main-power-supply-01sk4vtrndbaaguwe2brflsj-2-0.jpg
PMP3000
ziro-need-part-list-main-power-supply-01sk4vtrndbaaguwe2brflsj-2-1.jpg

You can download from this link.
http://elektrotanya.com/behringer_pmp3000_sch.rar/download.html
Hope this helps.
Regards.

Behringer Music | Answered on Jan 04, 2017 | 169 views


If it come back on after shutting down, you have a part overheatinga and then working again after it's cooled off, rather than "blown. You will need to take it in for service.

Behringer Music | Answered on Aug 31, 2015 | 839 views


The most common problem would be the headphone cable, particularly at the plug end. If they work fine on other systems, the next place to check is for a dirty headphone jack. Next a dirty/defective headphout out pot or cold solder joints where the pot or jack connects to the circuit board.

Behringer Music | Answered on Aug 28, 2015 | 36 views


You need to take it to the repair shop.

Behringer Music | Answered on May 17, 2015 | 63 views


There are a few images and some info online, although nothing very conclusive? I would try contacting the company, I do amplifier repair and deal with company's daily, most of the time they are more than helpful...

http://www.behringer.com/EN/Support/index.aspx

Behringer Music | Answered on Mar 04, 2015 | 604 views


I would contact a service center here Find Service Center

Behringer Music | Answered on Feb 27, 2015 | 77 views


It may be likely that you've blown a fuse. This will require removal of the amplifier unit from the housing. The fuse is a 100-120 V~: 6.3 A H 250 V. You should be able to find this in most places. If the fuse is not blown, then the unit must be sent in for servicing.

Behringer Music | Answered on Feb 20, 2015 | 115 views


Go to this site to download your manual.
http://www.manualsonline.com

Behringer Music | Answered on Jan 07, 2015 | 276 views


If it is one of the toggle switches on the front then IF you can get it from Behringer then it would likely already be soldered to the board. If you just want the switch try a site like mouser.com and search for toggle switch and then narrow your search from there. Not extremely easy, so contact any electronics service center and they may be able to help you as the switch is an standard off the shelf part. Good luck!

Behringer Music | Answered on Jan 02, 2015 | 51 views


Capacitor and/or fuse has blow.

Behringer Music | Answered on Dec 23, 2014 | 116 views


You'll need to give a lot more information on what is happening and what you are doing to get any help here

Behringer Music | Answered on May 16, 2014 | 42 views


It sounds as if the input is too low. what happens if you plug whatever is going into the stereo channels into a pair of mono channels. Or are you taking about the phono stereo tape input?
The stereo channels are line level whereas the other channels have both line and mic level inputs, what are you trying to put through the stereo channels? You must make sure the gain switch is set to the -10dB to get the most sensitivity (the mono channels have about -132dB max sensitivity BTW) You probably need a different mixer or possibly a submixer if you are needing more than 4 low level inputs.

Behringer Music | Answered on May 16, 2014 | 152 views


What you need will depend on what you are doing with it (what sort of venues and how you are making music - what sort of band/solo with backing track etc.) You will need a monitor with an amp or a powered monitor. The key thing is that you'll be able to hear the monitor mix over the rest of the PA. If you are just putting vocals through it you would possibly be best with a 12" but otherwise go for a full range unit with 15" and horn. Power wise I would suggest you need something capable of generating at LEAST 125dB unless you are in a quiet acoustic set. The SPL from the monitor is much more important than the power since power has little bearing on SPL.

Behringer Music | Answered on May 16, 2014 | 52 views


You need the correct rackmount psu, rated at 150 watts, I think it uses more than one rail volts so you can't use any old supply.

Behringer Music | Answered on May 15, 2014 | 183 views


Needs the effects board replaced. The board is about 2"x 3" is not too expensive and easily replaced. Contact Behringer or a Behringer service center for help.

Behringer Music | Answered on May 03, 2014 | 120 views

Not finding what you are looking for?
Behringer XENYX 2442FX Mixer Logo

124 questions posted

Ask a Question

Usually answered in minutes!

Top Behringer Music Experts

Michial Gueffroy

Level 3 Expert

1140 Answers

Chickenwatt

Level 1 Expert

18 Answers

Ric Weide
Ric Weide

Level 1 Expert

10 Answers

Are you a Behringer Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...