Behringer Europower Pmp5000 Powered Mixer Pmp5000 - Page 8 - Answered Questions & Fixed issues

Clean the sockets and switches with a good contact cleaner.

my peavy does that to me when I use a cheap extension cord,it has to be heavy duty cord,or plugged directly into receptical

http://www.gitarrenfundgrube.de/manual/Behringer-GMX110_GMX112_GMX1200H_GMX210_GMX212_M_EN.pdf Below is a link to Guitar Center which appears to have this instrument. Guitar Center Music Instruments Accessories and Equipment

It sounds like a n overheating problem. Some component is running too hot and shutting down. This will not be a user servicable problem and it needs to go into the shop. Discuss it with the shop when you take it in to be sure they will have access to the parts they need. Behringer is notoriously slow to ship parts so if it's an exclusively Behringer part as compared to a general electronic part you may have to consider replacing the unit depending on what time frame you have to work with.

Bad switch

There has to be some internal problem for a fuse to blow. Putting in a bigger fuse can only cause more problems.

Pray. Maybe the God is playing it.

Try www.elektrotanya.com - you can down load 2 manuals per day, else pass the electronics test to get more :-)

Hi, you didn't say if the mic actually passes sound? The C-1 is a condenser Mic & needs phantom power - switch on the rear of your mixer. If that's no help, what happens if you disconnect the mic, then turn the levels back up? Still hissing or gone? If it's gone then it's the Mic - must use a 3 wire cable, preferably XLR so it gets the phantom power. If the hiss is still there without the Mic then sounds like the mixer is faulty - try some of the other channels..... How loau is the hiss - just in the background or as load as a vocal "one, two" test? A few things to check anyway...... Good Luck!

Looking at pictures on line, you'll nee to remove the electronics panel - take out the screws around the rear edge at the back & the 3 at the top, behind the handle / in front of the panel. I would expect the panel to come out thru' the rear..... Be aware of the speaker lead - could be a bit short so you may need to disconnect it. Once the electronics panel (mixer & amp etx) is clear you should be able to get your hand inside / under the handle & undo the bolts. There's a possibility the if the handle is held on with bolts then there could be "blind" or "Tee" nuts under, so undoing the handle screws may be all you need to do? Take care though, because if they're normal nuts they could drop off into the gubbins! Good Luck!

It's probably not cost effective to repair it' Check the horn driver and the raw woofer to see if they are still good, and if so retain then as spares.

Sorry this site doesn't have this info.

It's always possible, but I doubt it's the fader. I'd suggest taking it to the shop for a hands on diagnosis.

i suggest you contact Behringer Customer Service for advixce. Without the setup in front of me, it's hard to figure out the wire routeing, switch positions, ect. that may be leading to this problem. As they would be the people most familiar with the gear, they'sd be the people to ask. http://www.music-group.com/support/behringer/askquestion

You can connect where it is possible. I hope you will understand.

On what channels from what source? Is it from USB too? have you got the gains set right? are you overdriving the amp? does the USB output distort as well?

I presume you are using the send and return inputs on the EFX500. Make sure the effect selector, CH Selector and EF On/off are set right. then use these in the insert chain of the mixer for the channel/bus/sub you want to use the effects on. Remember on the mixer it will be tip send and ring return. It would be useful if you said which behringer mixer (they make an awful lot of them from complex digital to simple DJ) and what you are trying to do with it. It is clearly explained in the Pioneer manual under basic connections. If you are a DJ you may not be familiar with the Insert concept so get yourself down to a professional sound/PA outlet or Radioshack / Maplin and ask for a pair of insert leads.

A bit more info about what you're you;re trying to do would be useful. You would normally use both these as inserts either on the main bus or more likely on an individual or subgroup bus, as you want them in sequence you'll come out of the insert send (tip) into the first unit (whichever you feel is best first) and then from its output into the input of the second unit, then from the output of the second unit into the insert return (ring)

This is going to be a nightmare. The only way will be in a daisychain with the crossover probably last, the sonic exciter before it, the virtualiser before that and the DJ mixer (which one are you using) at the beginning of the chain. What on earth are you trying to do? As a DJ it is likely most of what you play will already have been compressed to the limit so the multicom may not have much to do unless you're going to use it to reverse the effects of the exciter in which case forget both of them. I assume you're going to bi or tri amp so it is probable the crossover will be last as stated but trying to figure ANY way to get some use out of your list you might try the exciter in the Sub output of the crossover and the virtualiser on the mid and the multicom on mid top but this would just be trying to get anything of value from your list. Forgive me but it seems you really don't know what you are doing as the equipment you are listing is not really for DJing and certainly would not normally be used in the only way you could really use it in your environment. Did you get a job lot or something?

Once connected to the computer you have to open your Daw and find the menu to activate the mixer via midi. Check the user manual of your Daw. Also you might have to do some midi mapping to set up the controls.