20 Most Recent Behringer Xenyx 1832fx Mixer 18 Input 32 Bus with Efx USB - Page 4 Questions & Answers

Radio Shack may have the fans or can order it for you take the fan to a local Radio Shack store.

In order to help you we would need the make and model of the mixer.

Behringer recommends using a shielded CAT 5e cable with Ethercon connectors wired to the T568B standard to connect the two. Also you need to make sure that the board is completely powered on before turning on the S32 for proper connection. Make sure you are connecting between the Aes50A ports. When connected you should be able to see a green light next to Aes50A in the main screen. Then you will need to properly route the channels.

in what way? no power? dead?

https://www.manualslib.com/manual/1045668/Behringer-Ultratone-Kxd15.html

See if another audio source connected to the mixer produces the same results. Try with the same cable and then with another cable. The purpose of this procedure is to determine if it is the cable and/or the laptop. (Sound card problem???) or mixer. Is it ALL audio or just specific audio from for instance, a music application? Does it cut out using iTunes? The mixer may have a bad or oxidized input. Try a different input channel? Are you using headphones to listen? It may be the headphone amp? OR, if audio is produced via amped speakers, it may be the mixer output. Does the mixer have metering? Do the meters also cut out? Does the laptop do the same thing if plugging in headphones to the laptop directly (no mixer)?

You have given in detail which is helpful

I looked up what that unit is so I'm not uber familiar and this is before coffee, however, check your effects levels, possibly delays or echos are building up on an individual channel and adding to your total output making it clip. Even if you don't have the effects on output, they can work in the background and clip internally. Is the output sound affected? Magnetic interference is another possibility if you are running it close to pickups, recorders and other high power supplies. Trim levels set too high? I don't know your actual stage setup but these are a couple things I have experienced through the years. Ahh, here's coffee and a drink to you finding your problem.

https://www.fullguru.com/catalogsearch/result/index/?gclid=EAIaIQobChMIgMv_05ST4wIVh4uzCh2nIwqxEAMYASAAEgIGlvD_BwE&p=2&q=behringer+power+supply

needs service, if the inputs to amp are clean (test that yet)>)

Connect the two Behringer B215XL to the Right/Main Speaker Outputs. Monitor(s) would connect to the Left/Mon Speaker Outputs manual is here: https://assets.peavey.com/literature/manuals/xr684fand696f_manual.pdf

http://ewp.koncon.nl/images/ewp/manuals/mixers/eurorack_mixers843.pdf Free manual online at the link above:

Hi Ezra, for the failure you describe, you may have a problem with the Main Insert connectors, more presumably on the left, this connector has the function of interleaving some type of processor in the stages of the master L and R, and has some contacts internal that get dirty and produce false contact in the passage of the output signal Try cleaning it with some contact cleaner, put a small amount of cleaner and with the help of a plug, put it on and take it out several times in order to make the cleaner work, do the same with the right channel, because the same fault will appear. , sometime If this does not work, you would apparently have problems with the left master dimmer potentiometer on the corresponding electrical circuit I sent you the link to download the user manual of your Behringer I hope you serve my suggestions and manage to make the left exit work Greetings Franco Dosil Hola Ezra, por la falla que describes, puedes tener un problema en los conectores Main Insert , mas presisamente en el Izquierdo, este conector tiene la funcion de intercalar algun tipo de procesador en la etapas de los master L y R, y cuenta conunos contactos internos que se ensucian y producen falso contacto en el paso de la se?al de salida Prueba limpiarlo con algun limpiador de contacto, pon poca cantidad de limpiador y con la ayuda de un plug ve colocandolo y sacandolo repetidas veces a los efectosn de que el limpiador actue, haz lo mismo con el canal derecho, porque ya le aparecera la misma falla, en algun momento Si esto no da resultado, aparentemente tendrias problemas con el potenciometro atenuador master Izquierdo on el circuito electrico correspondiente Te envio el link para que descargues el manual de usuario de tu Behringer Espero te sirvan mis sugerencias y logres hacer funcionar la salida Izquierda Saludos Franco Dosil http://www.manualsbase.com/es/manual/downloadmanual/119881 https://manualsbrain.com/es/manuals/809021

Likely a Neutrik s102-84 PCB mount jack. Common at amp repair sites online.

I assume you have the neutron connected to the computer via a USB cable. Right? What kind of cable are you using between the neutron and the workstation? Will the neutron play midi coming from the computer? Does it interface with Band in the Box or a software sequencer (Logic,etc)?

Yes you can, but the questions is should I. the answer is no, unless you have the money to new equipment. Why would want to connect another amp? If some tells you can do it ask for a deposit equal to the price of new equipment.

That would depend on exactly what make and model sub you're using, but one possiblity would be to run it of the 1/4" main output jacks next to the XLR outputs.

Check out the left channel with an ohmmeter. Be sure to unplug it from everything. Even though it's newit still could be defective.

Bad switch

I just started 6 weeks ago and I've gotten 2 check for a total of $2,200...this is the best decision I made in a long time! "Thank you for giving me this extraordinary opportunity to make extra money from home. This extra cash has changed my life in so many ways, thank you!" Visit site: http://w­­w­­w­­.SalaryHD­­.­­C­­o­­m