20 Most Recent Toshiba e-Studio162D Copier - Page 2 Questions & Answers

check the fusing thermistor , thermoswitch, heaterlamp one of them is the cause of error h4

Here is the text from a tip I have osted here on Fixya. It is for the Sharp AL Series copiers but your Toshiba is made by sharp and the reset procedure should be the same.

To reset the H4 condition on just about any Sharp AL series copier press the following key's in sequence and as quickly as possible (with 4 seconds for the first 4 keys)
Press "C" then the far left key (exposure mode) then the "C" key then the far left again.
So in other words C, far left, C, far left
Some model's use 2 other initial codes, so you may need to use one of these 2 alternate codes to get your display to go blank. The rest of the procedure is the same.
Alternate codes are: #, * , C, * or pound,star,C,star and also
#, Interupt, C, Interupt
If done correctly the display should go blank.
Now key in 14 as if you were going to make 14 copies.
Now press the print button.
The machine should reset and the code should be gone.
9 times out of 10 this is a false code that pops up due to power surges or noise.
If the code comes back this means you have a heater lamp or thermal fuse (more common) failure in the fusing area and will need service.
Good Luck and Thank You for using Fixya.

L1 is a laser failure. Normally the motor that spins the mirror assembly has failed.

The drum counter reaches 25000 copies , it's time to change the drum and reset counter .
Enter the reset mode by pressing : # - * - c - * .
then press : 20 - start -01- start - CA - CA .
Hope this will help .

You did not provide the make and model of copier but this code is common among Sharp AL series copiers which are sold under various models. I have pasted my tip on the solution for this code so it should work for you.
L1 or L1-00 indicates Scanner movement failure. The scanner is the part under the glass that lights up and moves back and forth. So if you lift up the feeder so you can see the glass, turn the machine off for a few seconds then back on. Watch the movement of the scanner. It should move right and inch or two then back to the left. If all goes well the copier should come to ready. Lay a piece of paper on the glass and press the print button to watch the scanner movement. If it binds up or does not scan correctly there are 2 possibilities.
1) your scanner lock is engaged and is preventing the scanner from moving. Check the clear plastic dial located under the far left upper side of the copier, near where the paper exits the machine. Make sure it is in the unlocked position.
2) Your scanner rail is dirty and dry. This rail can be seen under the glass towards the back of the copier. The scanner rides on this rail. It is very common for these to get dirty and for the grease to dry up causing the scanner to freeze up on the rail. The glass must be removed and the rail cleaned and lubricated.
Just power off then on the copier to reset.

When this copier Scanner unite was not work properly or coverd dust sensor then show this error code L1-00.
Solve: clean all surface in thie scanner area. then solve this problem.

In the manual it says to "Turn on power while holding down the status button on the network expansion kit. Continue to hold down the status button until a beep sounds."

It looks like the default password was TOSHIBA which took me forever to find. The user name should just be admin.

this error is a fuser unit error. you cannot reset the error code without repairing or replacing the fuser unit.

Hi,

I think iwill be able to solve trhe problem, all you need to do is to go the scanning section of the machine,check and cross check the cory lamp setting{i.e.the mechanical setting in relation to the lenght between the mirror 2/3 and the copy lamp mirror base, then go to the lens unit and check the communication cableor the wiring harnesses for loose contact, follow the tips carefully the problem will be resolve.

Rate this solution
RNJ VINODKUMAR

E007 Fixing film sensor failure
The fixing film sensor is faulty. - Check the connector of the fixing film
sensor.
- Replace the fixing film sensor.
- Replace the DC controller PCB.

you need to call a canon technician to sort it out

check for a paper jam at the registration thats the area just before the drum unit it could be a small piece stuck or the sensor jammmed..Good Luck A

...the waste compartment is same unit in the drum unit...if you know how to take out the drum unit then you can see the waste compartment...but be carefull not to damage the drum...couse its will cost you a lot, the price of a drum is high...and if you can change the blade in the drum unit then you can emptying the waste toner...better call for the expert technician...

Hi:

That noise you are hearing is most likely coming from the fuser assy. What happens is the lower pressure roller is the fuser gets a flat spot on it and causes the thumping noise your talking about. As long as the print quality is ok I would live with it uless you want to pay a tech to rebuild your fuser assy.

Good Luck

Andrew

The correct buttons to push in order to get into the service mode on a 162D are [#] key, [*] key, [C] key and [*] key. Then you key in 14 - 00 and press the Start key. If that fails to bring your machine back on, you'll have to replace the fusing assembly.

can't be done

please do the following : press #, interrupt, C, interrupt when display goes off enter 14 and pess print button

I think iwill be able to solve trhe problem, all you need to do is to go the scanning section of the machine,check and cross check the cory lamp setting{i.e.the mechanical setting in relation to the lenght between the mirror 2/3 and the copy lamp mirror base, then go to the lens unit and check the communication cableor the wiring harnesses for loose contact, follow the tips carefully the problem will be resolve. see ya