LG F1402FDS6 Front Load Washer - Answered Questions & Fixed issues

Make sure the hinge is not the issue

actuator valve may need replacing that lets water into compartment.

The Beep on/off function can be set by pressing and holding the Option and Rinse button simultaneously. We turned ours off by accident years ago. Just fixed it after reading this in the manual

The AE error is indicative that there is a leak somewhere in the washer and it has triggered the flood protection device found at the bottom of the machine. What you should do is find out if there is indeed a leak. Try tilting it forward and find out if water will run out. If you can see water leaking from the water, locate the leak and fix it.

http://www.washingmachineadvisor.com

Is it plugged in? Did you check the fuse? Do you have GFI switches (red and black buttons on the plug) in any room that might be tripped?

www.lg.com/us/support/washers

sensor is not fully trip to open position check the sensor there must be a broken plastic thats prevent the sensor in open position the sensor is located inside the machine behind the door

Hi from retired Englishman in SW France,

If it is still locked after the cycle has finished I would gently suggest as a first step that you clean the drain motor/pump lint tray/filter. So many 'faults' are caused by blocked filters and many machines will not even go to rinse or spin or release the door lock if there is any water still left inside.
Following are my complete and hopefully 'coverall' pre-typed guidance notes for checking both the drain motor filter and the drain motor ;-0)

REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT (alternatively use a wet vac as sensibly suggested by VinnyB1234!)
If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!). These panels are either held on by (plasic) screws or will just pull off. Most filters are held in by a round cover/knob. Sometimes the filter will not come out with the cover and you will have to persuade it to come out to play.
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

The steamer unit may be overfilling. Check the water valve and see if it leaking. If it's ok, you will need to replace the steamer unit. Good luck

Replace cold water inlet valve assembly.

hi, the problem you are having is caused by the machine not sitting level all you need to do is adjust the feet so that the machine is sitting level, your going to need a spirit level and someone to help you tip the machine back slightly to got to the front legs all you then need to do is unscrew the legs until the machine is level from front to back and from side to side.
it may take a while to get right but once its level you will no longer have the problem you are having and also the machine will be a lot less noisy

To remove the drain pump filter on your LG washer model WM2016CW, try gently wiggling and pulling it after removing the cap. If it's stuck, apply lubricant sparingly and tap around the edges. Comparing with your mother-in-law's similar model might offer insights. If all else fails, refer to the manual or contact LG support for assistance.

You are using the wrong type of detergent. Use liquid instead of granulated powders. They don't dissolve in low temperatures. https://www.manua.ls/lg/wf-8071ttp/manual?p=8 ..

See LG Support site for error 0E LG Washer - What is a Front Load Washing Machine OE Error Code? ' LG USA Support

An nP display code indicates that there is a problem with the electrical wiring in the home and that no current is being detected at the heater.

This has a new fangled direct drive motor. Normally the fix would be to replace the motor controller or one of the capacitors on the board, but this has none of those, and appears to be run by one control board and that is no longer available. Try cleaning the connectors to the control board with electrical switch cleaner spray. Your best bet is to call for service and hope they can replace the part that is preventing the spin cycle. https://www.searspartsdirect.com/model/1nx1gwawbm-003204/lg-wm2688hwm-washer-parts Some videos on that issue ..

check belt if ok check under agitator possible bad cogs

Wrong washing deterjant being used and machine not leval . Google your machine with the error code and you find a u tube link on this that will help you

Question edited for clarity and toss in some CAPS.

DEFINING COMMON ERROR CODES

LG HVAC https://lghvac.com > resource-service > filenam... LED2. (Cooling LED). 1. Indoor unit return air thermistor has disconnected or has shorted out. 1X. -. 2. Indoor unit inlet pipe thermistor has disconnected ... 2 pages https://www.google.com/search?q=lg+lmn187hvt+error+codes ..

This is a 'front end loader'. https://www.google.com/search?q=front+end+loader Google LG (model number) light flashing No idea what you mean by drying light flashing in the cooling light to stainless and I have been reading the question since yesterday! ..