Ricoh Aficio 1035 Copier - Answered Questions & Fixed issues
I HAVE AN ERROR SC 322 WHEN i GO TO PRINT RICOH 1035
Error Code SC322:
1st laser synchronization error
The 1st laser synchronization signal cannot be detected by the main scan synchronization detector board even if the laser diodes are activated.
Possible Causes:
+ Poor I/F harness connection between the laser synchronization detector board and the LD unit.
+ Laser synchronization detector board out of position and angle of reflection not correct
+ Laser synchronization detector board defective LD unit defective
Not sure what your expertise is on this, but unless you know how to service the machine yourself, this one is going to require a service call...
There have been instances where toner drops onto the LD Unit and creates problems like this. About a month ago I replaced the Laser Synch. Detector Board in a 1045 for this exact problem and error code.
I'd start by cleaning up any toner on the LD unit, and re-seating all the electrical connectors on the laser unit. If that doesn't clear things up, it's probably one of two things, the LD Unit or the Synch. Board. I'd lean more towards the Synch. Board myself, but you never know...
1/12/2018 3:50:45 AM •
Ricoh Aficio...
•
Answered
on Jan 12, 2018
•
3,385 views
Can not find ip address on richo 1035. I tried to
Connect the machine to a router or a switch with a network cable.
In used mode, under network settings - set the machine to DHCP, so it will get an IP adress from the switch/router.
Print out a network status page, and see if you've got an IP adress.
In the command window on your PC type: ipconfig/all and see the IP adress of your computer. Compare it to the adress the machine got from the router/switch and see if they are almost identical apart from the last digits.
Install the driver, and install the printer using device name, and you should be good to go. Or you can set the IP you got from the switch/router as a static adress, and install the copier using the IP adress.
8/16/2017 12:03:17 PM •
Ricoh Aficio...
•
Answered
on Aug 16, 2017
•
226 views
Ricoh 1035 laser problem
sometimes
the plastic of the laser is turned by the heat proves to relax and to fit the
screw that holds the laser unit that is of the side of the drum while it raises
a millimeter with a screwdriver, this sometimes works.
Verifies that the glasses and mirrors well
be positioned correctly.
Other
Poor connection between the laser
synchronization detector board and
the LD unit.
Laser synchronization detector board
out of position
Laser synchronization detector board
defective
LD unit defective
12/25/2016 3:31:53 PM •
Ricoh Aficio...
•
Answered
on Dec 25, 2016
•
585 views
Sc 390 problem
could be bad developer powder or is depleted in developer unit. toner density sensor is bad. connector in back were unit slides in broken. this code means not seeing developer unit not install in copier. could be bad board. this copier is old i would replace for a newer one if you can do this.
3/5/2015 1:10:41 PM •
Ricoh Aficio...
•
Answered
on Mar 05, 2015
•
152 views
Reset error code
press the orange key for say three times and press '107' and place your hand on the 'clear/stop' key for about thrre times .
themachine will take you tothe system sp .
turn off the machine and tuen it on after about A MINUTE .
THANS
7/23/2014 6:13:29 PM •
Ricoh Aficio...
•
Answered
on Jul 23, 2014
•
94 views
Sc 322, sc 326 codes
Never heard of this happening to five machines before. Check the connections in the laser unit.
7/13/2014 5:41:02 AM •
Ricoh Aficio...
•
Answered
on Jul 13, 2014
•
2,105 views
Ricoh aficio 1035 error code SC121
sc 121 is related to optics section of your machine.check the lamp is
glowing .if so check the connection from optics to main board.
7/13/2014 5:28:34 AM •
Ricoh Aficio...
•
Answered
on Jul 13, 2014
•
1,258 views
Ricoh 1035 error sc 818
hi
this error happened when :
Incorrect Function DIMM installed in Slot #2 on Controller PCB. (Slot #2 is for PostScript Option only) so you can:
Reload System Firmware.
Replace Controller PCB
for fix that.
7/12/2014 8:33:42 AM •
Ricoh Aficio...
•
Answered
on Jul 12, 2014
•
705 views
Functional problem
change the td sensor below the developer unit or if possibly change the complete developer unit
6/5/2014 2:26:50 PM •
Ricoh Aficio...
•
Answered
on Jun 05, 2014
•
479 views
Ricoh aficio 1035 copier gives error code 390
TD sensor defective
TD sensor not connected or disconnected damage
Poor connection between the TD sensor and IO board
IO board defective
Toner supply defective
* Insufficient toner in developing unit
4/18/2014 2:52:56 AM •
Ricoh Aficio...
•
Answered
on Apr 18, 2014
•
160 views
Error code 1045
unplug machine , open the front door there should be a 1/4 inch by 1 inch 'window' showing numbers this is the copy count, on the backside of counter there is a small plug that is not plugged in - plug it into the counter, , plug copier back in back in and code should be gone
4/12/2014 3:46:20 AM •
Ricoh Aficio...
•
Answered
on Apr 12, 2014
•
82 views
Error code sc546
546 is an unstable fusing temperature:
-Fusing thermistor defective
-Power supply board defective
-Defective connection of fusing unit
3/3/2014 6:27:54 PM •
Ricoh Aficio...
•
Answered
on Mar 03, 2014
•
348 views
Not finding what you are looking for?