Ricoh FT5832 Copier - Page 3 - Answered Questions & Fixed issues
Help me : Ricoh aficio
sc982 is usually an error with the NV-RAM (non-volatile RAM). Have you recently replaced the NV-RAM? If so, it probably just isn't sitting right on the board.
Have you tried turning the machine off (with the main power switch) and turning it back on? If the error reappears, you likely have a problem with your NV-RAM and it will need to be replaced.
Sorry for the bad news, but hopefully this information will help.
3/4/2015 1:05:51 PM •
Ricoh FT5832...
•
Answered
on Mar 04, 2015
•
1,208 views
Removed collator from ricoh 4418
May I ask why you removed the collator? I think there is something in the advanced service menu that will get past this and allow the machine to go to "ready" mode, but I am not certain. Trying to find that now.
Thanks
Tim
10/5/2010 6:00:13 PM •
Ricoh FT5832...
•
Answered
on Oct 05, 2010
•
75 views
E-4
There should be another set of numbers after the e4 flashes. E4 indicates a problem with the transfer belt assembly,main drive assy or the drum thermistor. I'm afraid you will need a tech to figure this one out.
7/15/2010 6:50:00 PM •
Ricoh FT5832...
•
Answered
on Jul 15, 2010
•
395 views
Ricoh ft5832 code e5 47
E547 is a level A code (need to do a fuser SP reset, copier is inop) the fuser lamp continuosly stays on. Probably a shorted triac or fuser board problem.
4/16/2010 3:43:28 AM •
Ricoh FT5832...
•
Answered
on Apr 16, 2010
•
264 views
E-5 light is on. What does that mean? Can't use
When the copier detects the E507 condition, "E-5" is displayed in the copy counter. Hold down the "·" key, and "07" is displayed in the copy counter.
for reset thiscode.
When the copier detects the E507 condition, "E-5" is displayed in the copy
counter. Hold down the "·" key, and "07" is displayed in the copy counter.
It would be necessary to know as it is the code to be able to help it better
3/27/2010 4:28:45 AM •
Ricoh FT5832...
•
Answered
on Mar 27, 2010
•
140 views
Error code E 1 on my Ricoh FT4418
please press (.) so we could see the last two number. but most probably check your exposure lamp and thermistor. maybe they are busted anf need to be replaced.
2/3/2010 4:24:57 AM •
Ricoh FT5832...
•
Answered
on Feb 03, 2010
•
430 views
Hi, I am receiving an E-1 error message on my
The E 1 code is the exposure malfunction code.Please verify the exposure lamp continuity and the components(thermistor,thermofuse) continuity conditions.Reset the malfunction code to open and close the front door.
12/27/2009 12:56:13 PM •
Ricoh FT5832...
•
Answered
on Dec 27, 2009
•
157 views
Number of copies
The number of copies is indicated to mechanical counter and the electronic counter press SP modes and counter select.
11/10/2009 6:12:44 PM •
Ricoh FT5832...
•
Answered
on Nov 10, 2009
•
79 views
E-5 error code
E5 code refer to fuser unit.To dfisplay both digits press the Enter.
E 52 Fusing error 1 Defective thermistor,heater lamp open,defective main or ac/dc drive board.
E 53 Fusing error 2 thermistor in shortcircuit,fusing harness shorted or ac/dc power supply board defective.
E 54 fusing error 3 main board or ac/dc board defective.
E 55 Fusing error 4 rhermistor open,defective main board or fusing lamp open.
When E5 service call condition occur for safety reasons they cannot be cleared by turn OFF/ON the power switch.After repairing the copier turn ON the main switch.Enter in the SP mode and press 97.Turn the main switch OFF wait 10 sec and turn ON.
2/3/2010 6:08:24 AM •
Ricoh FT5832...
•
Answered
on Feb 03, 2010
•
561 views
I have an error message: E-940. Can anyone
E940 - Main Switch Error
The detection mechanism is as follows:
· The machine reaches the auto-off time.
· The solenoid mounted inside the main switch turns on for 3 seconds.
· If the main switch does not turn off, the solenoid is turned off for 1
seconds.
· The solenoid is once again turned on for 3 seconds.
· If the main switch does not turn off at this point, the solenoid turns off
and E940 lights.
Possible Causes -
The main switch is defective.
The main control board is defective.
1. Turn on the main switch.
2. Enter SP5-810 (SC code reset) and press the Enter key.
3. Exit SP mode and turn the main switch off and on.
9/15/2009 4:30:31 AM •
Ricoh FT5832...
•
Answered
on Sep 15, 2009
•
219 views
Not finding what you are looking for?