Mitsubishi WD-52525 52" Rear Projection HDTV - Page 4 - Answered Questions & Fixed issues
Green timer light no picture
Also known as the Green Blinking Light of Death.The repair on this is cheap but very time consuming and wit no gaurentees.There are 4 Capacitors on the DM board and 4 Capacitors on the Formatter board that are more than likely defective and need to be replaced. On the DM board the locations are C81A2, C81A3, C81B3 and C81B4. They will probably be swollen.On the Formatter board the locations are C8F19, C8F21, C8F22 and C8F27. Also will probably be swollen. The values of all 8 capacitors are the same. 1000MF/16V. Replace with value 680MF/16V.While you have the chassi ripped apart, check the power supply board as well. You should fine some swolle caps on it also. Replace with same value of the one you remove.Now once all of this is done and you put everything back togeather, you have a 50/50 chance of success. I have found that many surface mount caps can also go bad on the formatter board. If your repair does not work, then replace all of the surface mount caps on the formater board that are 10 and 16 volts.Good luck to you.
3/20/2013 4:38:00 PM •
Mitsubishi...
•
Answered
on Mar 20, 2013
•
65 views
Green light keeps blinking
Thats a very common problem with that model which is the V26 chassis. usually what happens is the capacitors on the DM and the power boards drain and then when power is testored the caps wont recharge. usually installing the V26 DM / Power repair kit which is listed at the top of the following page fixes the steady blinking led issue on that model DLP in about 80% of the cases the other 20% will have other issues but since your set lost power for over a few minyues i would assume its the capacitors.
http://tvrepairworld.com/mitsubishi_repair_kits
1/31/2013 6:06:31 PM •
Mitsubishi...
•
Answered
on Jan 31, 2013
•
41 views
Mitsubishi WD 62525 will not turn on
Just check whether any electrolytic capacitors you have changed recently have placed in reverse polarity. Electrolytic capacitors will have both (+ve) and ( -ve ) polarity, marked on them. The circuit board too will have these markings, and the legs of the capacitors must coincide with these markings. If any one among them has been placed in reverse direction, the voltage rail to which this capacitor has connected will go very low, and a short circuit indication blinking will occur. Check this first.
1/29/2013 11:04:23 PM •
Mitsubishi...
•
Answered
on Jan 29, 2013
•
62 views
NO SOUND
Did you go through the setup menu in the owner's manual? If not, that's the problem! THere is a menu in the TV internal software that gives you choices you NEED TO READ. Among them is the choice of audio!
1/1/2013 1:49:29 AM •
Mitsubishi...
•
Answered
on Jan 01, 2013
•
44 views
Yellow light keeps blinking
If the status light is blinking yellow it means the filter cover is open ( On the left side of televison)
If the lamp light is blinking yellow it means the lamp cover door is open. ( Behind front lower panel) If both covers appear intact the switches may be defective or not engaging properly.
12/30/2012 2:56:54 AM •
Mitsubishi...
•
Answered
on Dec 30, 2012
•
1,655 views
Mitsubishi 1080p 73'' DLP HDTV - Color distortion
This would be the little sensor on the light wheel. Its cheap, you can get them online for around $2. You will need to take the light engine out and remove the color wheel cover and remove the color wheel and then remove the sensor. You will have to desolder the sensor and remove it to replace with the new one. What is happening is the sensor is overheating and not tracking the color wheel properly there for the colors get messed up. Once you replace the sensor the tv should work like normal. The part is (Sharp GP2S40 Photointerrupter). It is very difficult to find because they are not made anymore. Most major online part stores do not carry them but I found a lot of them at Wright Hobbies. Good luck.
12/24/2012 10:25:42 PM •
Mitsubishi...
•
Answered
on Dec 24, 2012
•
1,766 views
No picture or sound on my mitsubishi dlp
The set should have the standard self check which even if it does not make it on would indicate where the problem might be: Note that if you unplugged the set it will delete the errors, you have to in that case turn back on and when it fails do the check again.
12/20/2012 2:00:37 AM •
Mitsubishi...
•
Answered
on Dec 20, 2012
•
61 views
YELLOW TINT ON SCREEN MITSUBISHI TV MODEL WS 55313
The WS is a picture tube type rear projection first produced as a 2003 model year set.A few questions and then a offer if needed.Did this happen suddenly or after a power loss?By reboot do you mean the recessed reset button on the front of the set?I will presume if you turn color off completely the screen is some other color than black and white?the offer: have you tried the Option menu this set has hidden, I can explain if needed.
9/2/2013 3:26:50 PM •
Mitsubishi...
•
Answered
on Sep 02, 2013
•
458 views
My mitsubishi wd-y65 has sound but screen is black
You are SURE the lamp is good....well...if you say so. However, it sounds like you have made audio connection but no video connection (or lost it or is incorrectly set). Try other input modes. See if you an bring up "setup". If so...you screen/lamp is working.
10/6/2012 4:18:15 PM •
Mitsubishi...
•
Answered
on Oct 06, 2012
•
155 views
Mitsubishi WD-62825
Green Blinking light and
I have the same problem with the green light blinking and the T.V will not come on. I have reset it and unplugged it and everything and still nothing. Can anyone help me
9/4/2012 8:13:31 PM •
Mitsubishi...
•
Answered
on Sep 04, 2012
•
623 views
Not finding what you are looking for?