Mitsubishi WD-52327 52" Rear Projection HDTV-Ready Television - Answered Questions & Fixed issues

Factory setting. Do a reset to this TV, and then check. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

buy a flatscreen and consider it a down payment on 2 years worth of bulbs

most likely the lamp. pt# 915P020010 Recommend Phillips, OSRAM, or Mitsubishi original, as others may not work at all or have a very short life. https://www.shopjimmy.com/dlplamps?tv_brands_select=Mitsubishi&tv_models=Mitsubishi+WD-52327

unplug it from the wall, wait 30 seconds, then plug it back in. i had the same problem and this simple solution worked for me. Good Luck!!!!

Have a look at the lamp first and the noise should be a fan.

follow the power into the set and to the power supply, a lot of these had puffed up caps on the power board kill the whole set-----You will not find it a real easy set to get into or open up

Connect RCA wires (yellow, red, white) from the box's "out" to the tv's Input 1 or 2 on the back input panel of the tv set. If you don't have RCA's you may use a RGA- jumper wire (cable wire made into a 4 ft segment by the tech or buy a short cable wire from the Walmart, Target, or Goodwill store) Connect this wire to the "cable in" on the tv and the other end to the "cable out" on the box.ADDITIONALLY make sure you have the right input settings selected on the tv with the input selection you make with the wire connection you choose.

The set should have lights on the front that blink when it does this--Lamp is possiblelamp Ballast is possible The set also has a error buffer that can be called up if shuts off--blink code on front of set.Another common issue is set will play for a while and shut off--which best describes your problem?

when you tune in a tv station or playing a dvd player. if you playing a dvd player maybe your vido cable is not fully insert the plug (yellow color) . The red and black/white are for the audio.

describing a optical light engine with growing defects---pixels in the display unit going bad

radioshack

the filter cover actually presses the coontact switch closed so the set can power up. You will need to have that switch depressed so the set will work then the filter cover will not be needed as long as the switch is depressed somehow.

Here is a link to the owners manual for lamp cartridge replacement. Specifically go to page 65 for instructions. Good Luck : )

http://support.mitsubishi-tv.com/files/oguide/WD-52327.pdf

The tv board that call the Ballast board it is also dead too.This ballast board only job are to ignite the tv projection lamp only.

The status light blinking red is indicating that a fan has stopped. which is not allowing the set to power up.

cmurray12,

You do not have a bad fan, you have a bad optical disc drive. See my tip at http://www.fixya.com/support/r4160054-replace_color_wheel_in_dlp_projection_tv for the replacement procedure and where to get the parts.

Thanks for using FixYa and for the great rating.

hardrocko

Hi Brent, Mitsubishi's have a problem with the power supply and the Light Engine which incorporates the Digital Module of which it has to be purchased as a complete assembly. I sincerely believe you should not put that kind of money into a dlp set. The cost of the light engine is in the area of $1100.00. Your last idea is the best one.

Tv have jumping picture and go out are not the projection lamp problems."Jumping" Horizontal or Veritical high votage area circuitries have dead parts,must hire a tv tech. to trouble shoot and replaced parts to solved "H" or "V" hold tv to work.Tries many tvs shops,tries get the prices best qoutes and get it repair.

In general this happens when it has problem in the feeding source they can that there are a few blown or burst filters