20 Most Recent Mitsubishi VS-55609 55" Rear Projection Television - Page 8 Questions & Answers

These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/ Blinking codes details to many popular brand TVs are given. Surf the site with patience. If blinks continue without any pause, the main board is faulty. Counting of number of blinks to Philips TVs is entirely different to that of other brand TVs. It is not a direct count procedure. The site have details about how to count the number of LED blinks [Fault Codes] to Philips brand TVs are given; along with details of the faulty circuit location.

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent.

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Try plug and unplug headphones, see if sound comes back, could try a reset of tv.

The was a previous answer on Fixya ( John Betancourt Apr 25, 2019 What I did I open it up and removed the panel and clean out the fan.it was very dusty.) I'm not sure that it will fix you problem but if it does let me know. There's a video on youtube which will a bit more helpful. It's called "Mitsubishi DLP TV Repair - TV is Blinking - How to Identify Blink Codes & Fix DLP TVs". https://www.youtube.com/watch?v=INird71KKtA

Have the internal voltage regulator checked. Possible that it's failing.

anytime something is taken apart, the reverse procedure invariably leaves something out. recheck everything b4 creating a projectile.

Hi Patrick, I pass the link to the service manual of your Mitsubishi TV I hope you can resolve your concern Greetings Franco Dosil Hola Patrick, te paso el link del manual de servicio de tu TV Mitsubishi Espero puedas resolver tu inquietud Saludos Franco Dosil https://elektrotanya.com/mitsubishi_wd-60638_65638_73638_60738_65738_73738_82738_65838_73838_82838_60c10_65c10_73c10_chassis_v43_v43c_v43-plus_sm.pdf/download.html

I have a Mitsubishi WD73642 model which I'm having a problem with it turning off. When power is turned on the status light flashes green and appears to be powering up. Then u hear sound. Picture comes on light turns sold green then within a minute the El TV will just turn off no other dianososis lights. TV is not located too close to the Wall. Any ideas why?

The bulb is out. You can purchase on amazon for around $20.00. It is a very simple fix. Should take about 5-10 minutes

Sounds like its overheating.
Are the fans working properly?

Did you buy a quality bulb (or one of the cheap junk bulbs around $20-$30?)

The volume button on the remote or the TV is stuck. Try this first, Turn the TV on from the TV (put the remote in a different room) now turn it down from the TV if the volume stays down, the remote up volume is stuck. If it stays loud The main TV board needs to be replaced. If it stays down carefully take the remote apart. check for tiny screws in the batteries compartment if no screws it all clips. Now clean the remote (try not to touch the curcit board).

Do you have the model number available? It should be on the back or bottom of the unit. Before adjusting, clean the heads and verify that the tape is running at the proper height past each head. There are three head assemblies to inspect: the rotating video head, the stationary sync head, and the stationary audio head. The sync signal is on the top edge of the tape and the audio signal is on the bottom edge. If the sync head or an adjacent guide pin has come loose, that could cause tracking problems. Caution: the video heads are very delicate. They're located in the slots at the bottom edge of the rotating drum. Use a foam-tipped swab with straight isopropyl alcohol, and gently wipe the heads in the same direction as the tape goes (do not wipe perpendicular to the tape direction; you could snap the head off if it snags on the swab).

No error code 61 listed, only a 66 error code which indicates lamp issues: 66 A) Lamp did not turn on at P-ON sequence... Check CJ4 circuitry B) No Lamp Inserted............... No Lamp inserted C) Disconnected cable between ballast and lamp.... HV connection or lead wire to lamp. D) Lamp-Enable goes to PWB-MAIN but not to Ballast....Lamp Cartridge Failure for lamp see the following web site: http://www.shopjimmy.com/dlplamps?tv_brands_select=Mitsubishi&tv_models=Mitsubishi+WD-73638 recommend using the manufacture part# as many replacements for Mitsubishi will not work.

Shorted circuit board.

It might help to unplug the TV from the AC outlet for a few minutes, and hope that it's circuit resets itself.

Could be you need to set the output volume on your receiver for the soundbar. Most receivers allow volume output for each speaker

https://www.youtube.com/watch?v=_ONPuB5L-x4 https://www.youtube.com/watch?v=C9uA1DcyeNI https://www.youtube.com/watch?v=INird71KKtA