Mitsubishi WS-55511 55" Rear Projection Television - Answered Questions & Fixed issues
Tv turns on then off after a few seconds.
Try this and let me know what you find:
Normal
0
false
false
false
MicrosoftInternetExplorer4
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
MOST OF THESE SETS HAVE A SELF DIAGNOSTIC:
UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER
LIGHT COMES ON FOR A MOMENT AND GOES OFF.
PRESS AND HOLD “device” and “menu” buttons on front of tv
for at least 5 seconds and then release both together.
Watch for power light to blink in a sequence:
1 blink-then 2 blinks-------no error
2 blink-then 1 blink-------X-ray protection
2 blink-then 2 blink-------SHORT PROTECTION*******
2 blink-then 3 blink---------deflection circuit problem
2 blink-then 4 blink---------vertical circuit problem
******2, then 2 is most common---usually means one of the
fuses that protect the Convergence IC or IC’s is blown---set will detect no
voltage to convergence IC and shut down.
SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES AND THEN TO
GET IT TO REPEAT MORE YOU HAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.
IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM
let me know what you find--hope that you find 2 blinks, a pause and two blinks--this is the most common and easiest to fix.
if this has helped you rate this solution as I do this here for free.
SD TECH
10/4/2020 5:26:18 AM •
Mitsubishi...
•
Answered
on Oct 04, 2020
•
7,881 views
After a power outage the
i have encounter many of these issues with TVs going bad after a power outage which i something that can be complex. Actually almost all the TVs go through this issue sometimes in their life time.
What happens is that TVs have a circuit that controls the on/off phase; the circuit has resistors, diodes and capacitors to do the job. When there is a power surge, which is what happens when the power come back on, a diode, resistor or capacitor goes bad. Capacitors are the main ones that fail under a power surge/outage because they have a set of value assigned to them. The worst that can happens also is that a power transistor can go bad. The unit controls or regulate the power going in to the set.
So, if your TV does not turn on, turns but goes dean right after, or has the standby light flickering; you would need to have it check by a technician. On the other hand, you might want to check if its not just a reprogramming that the set needs.
12/17/2017 11:17:46 PM •
Mitsubishi...
•
Answered
on Dec 17, 2017
•
98 views
Power button bilinking
Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://homenol.blogspot.com/
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "
brand name" to your device,
[Exclude the model number] in the "
Search box at the top right of the display window of the Homepage" to get gathered related posts.
11/9/2017 7:03:28 AM •
Mitsubishi...
•
Answered
on Nov 09, 2017
•
53 views
Cracked front glass
U out of luck,not worth to replaced the screen,the screen it same as the new tv.The tv compannies sell out tv screen as a new tv.The tv 95% worth is in the screen.
1/25/2015 7:33:10 PM •
Mitsubishi...
•
Answered
on Jan 25, 2015
•
233 views
Need to reset input code on Mitsubishi tv with
In the advanced menu from the main you should be able to navigate to the lock input, when you try to unlock the input it will ask for the code. Just press the QV + 9 and this will unlock the input.
Then you can either create one or just leave it unlocked.
I hope that this helps you with this issue.
Thanks for usning Fixya.
asnowman
1/22/2015 10:27:49 PM •
Mitsubishi...
•
Answered
on Jan 22, 2015
•
1,113 views
What is the system restore and how can i replace it
system restore is usually a software function (although some devices have the ability to do a system restore from a button somewhere on the device - check / download your user manual for specific details.
As for replacing system restore, in short, you cannot. System restore takes an item back to factory state and even if you could you would not want to replace this.
11/24/2013 7:47:09 PM •
Mitsubishi...
•
Answered
on Nov 24, 2013
•
87 views
My model is a WS-55511. I turn on the TV, the
Normal
0
false
false
false
MicrosoftInternetExplorer4
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
MOST OF THESE SETS HAVE A SELF DIAGNOSTIC:
UNPLUG TV AND THEN PLUG BACK IN---TURN ON---GREEN POWER
LIGHT COMES ON FOR A MOMENT AND GOES OFF.
PRESS AND HOLD “device” and “menu” buttons on front of tv
for at least 5 seconds and then release both together.
Watch for power light to blink in a sequence:
1 blink-then 2 blinks-------no error
2 blink-then 1 blink-------X-ray protection
2 blink-then 2 blink-------SHORT PROTECTION*******
2 blink-then 3 blink---------deflection circuit problem
2 blink-then 4 blink---------vertical circuit problem
******2, then 2 is most common---usually means one of the
fuses that protect the Convergence IC or IC’s is blown---set will detect no
voltage to convergence IC and shut down.
SET WILL REPEAT BLINK ERROR CODE UP TO 5 TIMES AND THEN TO
GET IT TO REPEAT MORE YOU HAVE TO UNPLUG SET AND TRY TO TURN ON AGAIN.
IF IT IS 2 AND THEN 2---USUALLY
CONVERGENCE CIRCUIT PROBLEM
4/24/2013 1:12:49 AM •
Mitsubishi...
•
Answered
on Apr 24, 2013
•
611 views
Won't power on
Check the Mitsubishi TV error codes using the instructions on www.TvRepairKits.com . Look on the tips page. If its a steady blink its likely the blinking light of death issue. If its a 2-2 pattern its likely a convergenec failure. Both are failry easy
DIY tv fixes.
4/19/2013 7:32:29 PM •
Mitsubishi...
•
Answered
on Apr 19, 2013
•
60 views
TV won't turn on
Do you have any lights on on the front of the TV? anything flashing? Or is it just dead?
3/21/2013 12:45:53 PM •
Mitsubishi...
•
Answered
on Mar 21, 2013
•
64 views
Where is the dm board for ws-55511 located
The dm power board is the small board shown in the illustration below it has the 7 capacitors on it and its located inside the metal box on the far left side of the TV when looking in the rear cover. The metal box stands up vertically
2/12/2013 9:52:09 AM •
Mitsubishi...
•
Answered
on Feb 12, 2013
•
176 views
Not finding what you are looking for?