20 Most Recent
JVC AV-56WP30 56" Rear Projection Television - Page 6 Questions & Answers
Convergence problem?
You will need to change the two convergence ICs they are both STK392-110 and you may also need the convergence resistor kit for your model. You can get replacement ICs and resistor kit at the following link and they provide free instalation instructions with pictures.
http://servicemanuals.vstore.ca/
Double pictures
There is two ICs on the left side of the printer wiring board.that board is separated from other boards
56WP30 Convergence repair
Convergence amp ic bad
http://home.earthlink.net/~oleg.filippov/ConvergenceFix.htm
http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html
http://www.hdtvoice.com/voice/showthread.php?t=28929
SERVICE MODE
I have a tv bluesky model PR14 .can anyone help me with service mode-
Jvc AV-56wp30
http://home.earthlink.net/~oleg.filippov/ConvergenceFix.htm
http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html
Sony Convergence
http://www.techlore.com/blog/entry/19694/Sony-Convergence-Repair-My-Sony-TV-has-a-distorted-picture-/
http://www.techlore.com/article/19631/Sony-Convergence-Procedure/
Stk392-110 v stk392-180
Actually I would go and have gone with many times, the STK392-150's They handle more wattage than the original 110's but don't draw as much current as the 180's, which is good for the surronding resistors. It is a good balance and has worked for me many times. Hope this helps.
Picture quality
You need to replace the two convergence Ics STK392-110 they are located on the small board up front. behind the speaker grille and access panel. You can get new ICs at the following link as well as free instructions on how to do the repair yourself and save several hundred dollars for a 30 minute repair. Here is the link.
http://servicemanuals.vstore.ca/
Covergence problem
Convergence amp ic bad
http://home.earthlink.net/~oleg.filippov/ConvergenceFix.htm
http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html
http://www.hdtvoice.com/voice/showthread.php?t=28929
Or send to ptscorp.com
http://www.hdtvoice.com/voice/index.php?s=
good luck
please mark the post with a fixya
TV won't turn on
Sounds like you have had a powersurge during the night.
The power supplies on both units will have to be inspected and repaired. The expense for this type of thing can grow rapidly depending on how much damage has been done.
Check your other appliances and see if they are all OK like the washing machine other tv's etc.
If there was any kind of storm activity during the night it could have also been a lightning strike to the antenna.
Hope that helps.
No Audio
1. Make sure you have connected the cables from audio OUT on the Directv box to the audio IN on TV input 3 and have selected the correct source on the TV.
2. Many sat boxes have an audio volume control. Select the satellite box on the Directv remote and turn up the box's volume.
Hope this helps.:)
Convergence problem on JVC
Convergence amp ic bad
http://home.earthlink.net/~oleg.filippov/ConvergenceFix.htm
http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html
http://www.hdtvoice.com/voice/showthread.php?t=28929
Sound
Menu Then Center Ch Input Then Make Sure It Is Off
Bill
TV IS GREEN
gave the crt's a little rat-tat-tap be careful!!!!!!!!!!!!
There are other possibilities as well. Look at the front of the green
projector tube and see if it looks like the cooling liquid has been
leaking out or if it is not clear all across the screen.
could also be convergence ic's
Convergence
why are you spending so much! you could get the board repaired for a fraction of that ptscorp.com
or do this yourself.
Convergence amp ic bad
http://home.earthlink.net/~oleg.filippov/ConvergenceFix.htm
http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html
http://www.hdtvoice.com/voice/showthread.php?t=28929
Not finding what you are looking for?