20 Most Recent JVC AV-48WP30 48" Rear Projection Television - Page 7 Questions & Answers

The "hd cord" you're using is probably a DVI cable; they don't pass audio. For this to happen, you need an HDMI cable.

These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

Convergence problems are very common on all Projection TV sets including Sony,Samsung, JVC, Philip Magnavox, Panasonic, Akai, Pioneer, Hitachi, Zenith, and others. You can get a convergenece repair kit wiith instructions from the links below.

Here are some of the most common problems with these sets...

Problem #1) Convergence

Yours may have one or more of the following symptoms

• Screen Looks 3-D
• Colors wont align
• Screen may look distorted or warped
• No Audio/Video - makes a chirping sound.

Problem #2

Another common problem is dull or washed out video.
Your TV may have one or more of the following symptoms....

• Dull looking picture
• White looking picture
• Halos around objects
• Red/Orange looking picture

You can see some more examples and find a fix here
http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

These sets have several common problems which are listed below.

Problem #1) Convergence

Yours may have one or more of the following symptoms

• Screen Looks 3-D
• Colors wont align
• Screen may look distorted or warped
• No Audio/Video - makes a chirping sound.

Problem #2

Another common problem is dull or washed out video.
Your TV may have one or more of the following symptoms....

• Dull looking picture
• White looking picture
• Halos around objects
• Red/Orange looking picture

You can see some more examples and find the fix here...

http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Ur convergence are dead.Must know how to solders?Have solder iron,solders,solder wicks?Must replace 2 STK convergence IC,and some or all it resistors.Tries websites to buy a convergence kit at Tv repair Wolrd.com,Tvrepairkits.com to repair it ur sself.The shop will cost $300 for parts and labors.

you will need to install a convergence repair kit. You can get the convergence repair kit for your model at www.tvrepairworld.com which also contains the CD with step by step instructions for the repair.

Bad chips...There are a ton of cheap fakes out there....Or bad resistor...

Projection TV sets have several common problems listed below.

Problem #1) Convergence

Symptoms:

• Screen Looks 3-D
• Colors wont align
• Screen may look distorted
• No Audio/Video - makes a chirping sound.

Example Photo:

Problem #2 CRT Fluid has clouded over.

Symptoms

• Dull Video, Washed out
• White/Bright looking video
• Halos around objects
• Red/Orange looking

Example Photo:


You can see more examples and find a fix here...

http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Projection TV sets have several common problems listed below.

Problem #1) Convergence

Symptoms:

• Screen Looks 3-D
• Colors wont align
• Screen may look distorted
• No Audio/Video - makes a chirping sound.

Example Photo:

Problem #2 CRT Fluid has clouded over.

Symptoms

• Dull Video, Washed out
• White/Bright looking video
• Halos around objects
• Red/Orange looking

Example Photo:


You can see more examples and find a fix here...

http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

If you try to adjust convergence with the flash focus, perfect focus, (depending on the make of your set) or by manual convergence and the lines will not line up or even move. Your symptom sounds like a damaged convergence IC.

If you want to repair this set yourself, I have some instructions below that will be a help to you.
While it is not a very hard repair, this repair can be a bit tricky. If you have a 45W soldering iron, solder, solder wick, heat sink compound, and some basic soldering skills, you can repair the television yourself.
*** VERY IMPORTANT NOTE***
If your set is not producing a clear picture and the colors are not lining up, do not continue to watch the set as this can lead to further failure and possibly damage the individual CRT’s in the set.
I have repaired hundreds of these sets, so if you have any questions after reading the following, please reply to this post and I will help you in any way that I can.

With that aside I have some support suggestions that I have put together that may help you make an informed decision.

You should be able to get a local service center to repair this at your house for between $350.00 - $450.00, If you want to repair this set yourself, I have some instructions below that will be a help to you.
While it is not a very hard repair, this repair can be a bit tricky

How do I tell if the IC’s are damaged?
Since you cannot look inside of an IC, you will have to locate some of the components in the area around the convergence IC’s. You may be able to see some resistors that have changed colors or you test a resistor and it no longer reads the value marked by the color bands or the printed value. You will have to replace the IC’s and the supporting components.

When you remove the old IC's, please be sure to remove all of the old heat sink compound, as it can act as an insulator for the new IC's and cause them to overheat. I usually clean the heat sinks with alcohol and a small rag.


Where are the IC’s located and how do I find them?
There are two and large IC’s that control the convergence in a big screen set. Some of the newer sets only have one. If you only have one, it is right in the middle of the set on the center circuit board. They are secured to a very large aluminum heat sink. They will have a part number stamped on them that will start with an STKXXX-XXX, like STK392-110.

Along with the convergence IC’s there will also be some associated components that will need to be replaced as well. There are some resistors that are part of the convergence circuit that will be open and need to be replaced. Most likely these will appear charred in the center. If you have an Ohm Meter or a DVM, check all the resistors that are close to the IC’s and you should be looking for either ones that have opened or have changed values.

If one of the convergence IC’s are found to be bad, I would replace them both, if one has gone bad the other may go soon. I usually order my parts from Andrews Electronics in California, they will have the OEM components that you will need.
Their site is http://www.andrewselectronics.com/welcome.aspx
And their phone number is a 24-Hour Order Desk: (800) 274-4666
I recommend the phone order so you can talk to the person about the different types of IC’s that are available.

I would also advise that the convergence IC’s be OEM or better, just because they are cheap does not mean that they are a good deal. I have seen the cheap IC’s fail after a short time, even though they look exactly like the OEM IC’s. I think that the bottom line is that you will get what you pay for when it comes to the parts.

You can also try http://www.tvrepairkits.com/ , they do carry OEM or better parts. When you order from them you will get a kit with instructions on how to do the repair, step-by-step.



I hope this information allows you to resolve this issue.
If you need further assistance please comment to this post and I will try to help you further.
Thanks for using FixYa
asnowman

I have attached some photos of really bad convergence problems; your picture may not be exactly as bad as these.

Sorry ,that you have been having more problems ,Let me check files on your TV and I will get back to you . Right now my computer is down with virus and Im having to rebuilt programs. Had to borrow friends computer untill I can fix that one. Was wondering did you Enter service mode for convergence alinement and correctly Save and exit SM.

some how the convergence ckt went bad,common problem to pj televisions.

Goto www.TvRepairKits.com and get one of their kits with instructions.

Its a convergence problem. You may want to check the site www.tvrepairkits.com. Every thing they said every description was right on. The best money I ever spent and the confidence you get from doing it yourself, Its a great feeling of achievement not to forget the live messenger support is instantaneous, friendly and informative if you need to fix your tv go to tvrepairkits.com I fixed a philips 60 inch tv in 45 minutes, The convergecne chips were bad thanks a million. You guys saved me 250.00 bucks. I'll be recommending you to everyone I know!

you need to install the RCA repair kit called the ITC222A convergence option missing repair kit from www.tvrepairworld.com the kit has the Cd with instructions.

Thats the classic sign of failed convergence ICs and resistors. You can get the convergence repair kit for your model at www.tvrepairworld.com the kit contains the parts and the Cd with instructions.

Hi

Thanks for using FixYa. It seems you might have to change the board completely, also check the resistors as if they go bad you might have to do the repair again. Another reason could be the cold solder joints left out on the board and if the TV is too old then replacing the board completely will solve the issue, you can get a new one for around $65. Please do accept the solution if the issue is resolved or else revert for further assistance.

Thanks
Rylee

U know how to use a multimeter right?Check and replaced all the resistors near the 2 convergence ICS.Most resistors are big and blue core in colors.

WELL IF IT WAS A LOUD POP,YOU NEED TO REPLACE THE FLYBACK TRANSFORMER,GET THE MAKE AND MODEL # AND DATE OFF THE BACK OF TV, AND CALL MATS ELECTRONICS #1-800-628-1118

Ur convergence is dead.Must replaced the 2 convergence ICS and all it resistors.The shop will cost U $300 for parts and parts.

sound like the convergence ic is defective also look for burned resistors on the small pcb that the convergence ics are on

Hi


Thanks for using FixYa. From what you have described it seems that you have to replace the convergence IC and check power resistor for leakage, if values are not exact you have to replace them. The typical cost to get this fixed by a pro is about $300 - and it doesn't mean that he/they will do a job better than you do. The parts are less than $100 (about $20-$30 for the IC's) if you want to do it yourself. Replacing only the IC's MAY solve the problem; however, many people have also had blown resistors requiring replacement. Why would you ask should you replace both of the IC's if only one is shot?! If one is shot the other one is not far away and for that little price of the chips it worth changing them both at the same time. Also the convergence board should be checked for cracked solder. If you replace the ICs and the resistors are shot, the ICs may blow again almost immediately, meaning you may have to do the repair twice.


Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee