I can't find the remote control code for this ilo 2600. I tried the codes il02600, ilo2600, ilo2600 and noe of them worked on the websites. Please help. I will even buy a new one if possible.
I finally found a direct tv remote code for my Ilo television. It was 10171. Others you can try that were for Direct TV remote: 10154 10236 10463 10180 10178 10019 10177 10623 10179
Posted on Apr 27, 2009
the volume does not turn up or down and the remote buttons do not work except the power button and the buttons on the tv set dont work except the power volume channel or input do not work if anyone can help solve this it would be appreciated if not. A number for the Ilo company to talk to somebody there.
I just used the following instructions from this site on my 'totally dead' Ilo remote and it worked like a charm! I did step 2 twice on each key and put the batteries back in and it worked great! Hope this helps you too. "Dead" Remotes Can Be Saved How to Re-Start Your "Dead" Remote Control This only takes about a minute and will restart 1 in 3 "Dead" Original Remote Controls. Good Luck! Step 1- Pull the batteries out of the remote and leave them out until Step 4. Step 2- Press and release each and every button one at a time on the remote control until every button has been pressed and released at least once! Step 3- If your remote has slide switches, you must move the switch to each position then repeat the button pushing in Step 2. (When you're done, be sure to put the slide switch in the correct position to operate the unit the remote came with!) Step 4- Put the batteries back into the remote, being very careful to install them correctly. New batteries should be used if you're not sure about the old ones. Step 5- Try the remote. If it works, Great! If not, it's time to call 1-800-Remotes or use this website to order a new remote.
Posted on Jan 23, 2007
i need codes for my universal remote control for my ilo television?
Here are some to try, mine was 0189, but there are many to try. 0051 0189 0053 0198 1070 1024 1023. I think some listed codes for Emerson work as well.
Posted on Aug 06, 2008
I'm trying to program my ilo TV to my direct TV remote control, but the TV is not listed in the list of TVs. Would another TV name work?
Ilo is made by Orion and/or Sansui.
My Ilo dtv2794B was programmed on Direct TV remote as follows:
In Direct TV mode press 'menu' .
Go to parental ,faves setup
Go to system set up
Go to remote
Go to TV
Select brand (Orion)
Follow directions from this point.
Good Luck>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
Posted on Jan 07, 2009
MY TV WILL NOT TURN ON. THE POWER LIGHT GOES FROM GREN TO RED9SYANDBY) IMMEDIATELY.
IS IT THE TV OR THE POWERCORD?
my tv is doing the same thing i am fighting with wal mart right now my tv was only 1 year old on day i tryed to turn it on and it would not so im trying to get to the biottom of it right now call this girl named lalasha at 479 204 6805 she might be able to help u
Posted on Mar 09, 2009
I don't know how to make the HDMI work on my TV. I have a HDMI cord connecting my PS3 to the TV, but when I select HDMI in the Videomenu a blue screen appears,a dn it says No Signal
don't know how to change hdmi input
it sounds like there is a problem with either the output on the PS3 or the input on the circuit board of the TV. I would try a reset on the PS3 first. Also make sure that there are no other video or audio cords plugged into the PS3 because this will cause the PS3 not to send the signal via the HDMI.
Posted on Mar 17, 2008
Hi, do you have any info on the above code? If not, do you have any idea who manufactures the Clarity LCD TV's (as bought in Tescos). Many thanks in advance.
I have decoded the remote code from my 32"
the code is 1239
if you need further help then please email [email protected]
Thanks
Posted on Jan 31, 2009
I turned my tv off as I do everytime I leave my home. But this when I returned it would not turn back on... the red light on front would not turn green as it normally would. I tried unpluging it for a couple of minutes but nothing changed. Any suggestions would be so very appreciated. Thank you for your time.
I had this same problem (power supply). If you are reasonably skilled with a screwdriver, you can fix this for $70. Contact TMX Logistics 915-772-5991 ext. 1653, they will give you a number to ilo to get a case number (I have lost number they gave me). Then call TMX again and they will fax you a form. Fill out form and fax back to them. Then call TMX again to order part with credit card. Part number is 6693006610. Here is a link to a service manual for your TV with detailed instructions on disassembly.
http://pettersservice.com/polaroid/docs/FLM-3001ServiceManual.pdf
All of the parts are modular, so it is fairly simple.
I received the part from TMX 4 days after ordering it (FEDEX ground) and finished the repair in about 20 minutes yesterday. The above pic is the TV hanging on my bedroom wall today.
I gained all of this info after frantic search on the internet and numerous calls to various service centers. Hope it saves somebody some legwork.
Posted on Aug 02, 2008
This is an encrypted channel
Hello hbennett,
When looking at cable TV some of the channels are encoded (arranged digitally) to disallow access to the content on that channel. This is true in the case of encrypted channels, the cable company has taken that channel and through an encrypting algorithm made that channels content inaccessible to you. The only legal way to see that channel is to pay the cable company or content provider for that service (channel). I hope this helps.
Thank you,
Shuttle83
Posted on Jan 24, 2008
i have a rca universal remote control & i need the code for an iLo tv to program it
Checked on line for any code there was that someone used for iLo t.v.'s, found two codes on your site that someone had used & used those & one of them worked. Thanks again!
Posted on Apr 02, 2008
393 questions posted
Usually answered in minutes!
739 Questions
153 Questions
174 Questions
153 Questions
114 Questions