20 Most Recent
Canon imageRUNNER C3200 Copier - Page 2 Questions & Answers
Error code
HI
Machine error E0020-01a9 is developer problem
1/29/2016 2:34:01 AM •
Canon...
•
Answered
on Jan 29, 2016
What is the permanent solution
This problem was in with the IR-C3200 problems. The E020 codes have to do with either toner or the color drums. This is most lilely an error with one of the drums. The fist 2 digits indicate the color of drum. 01 is Black, 02 is Magenta, 03 is Cyan, and 04 - Yellow.
For the IR-3530, then you have a problem with the toner. The error code in the book says that the path between the sub hopper and the developing assembly is clogged with toner. This assembly will have to be removed and checked for the obstruction. Hopefully you don't have a finisher on these copiers because you will have to remove it to get to the toner hopper assembly. Good Luck.
1/20/2016 5:41:15 PM •
Canon...
•
Answered
on Jan 20, 2016
I have photocopier Canon imageRUNNER 2530i and it showed the problem with code E000000
It appears your machine suffered a power surge and must be reset. http://okb.oceusa.com/service/main.jsp;jsessionid=AD324B614CBFCAC0264A5C5AC20E3A60.node6?t=solutionTab&ft=searchTab&ps=solutionPanels&locale=en-us&_dyncharset=UTF-8&brand=oce&curResURL=%2Fservice%2Fmain.jsp%3Bjsessionid%3DAD324B614CBFCAC0264A5C5AC20E3A60.node6%3Ft%3DsearchTab%26_dyncharset%3DUTF-8%26brand%3Doce%26locale%3Den-us%26lstLanguageQuery%3Den-us%26lstLanguageResults%3Den-us%26sfield%3D%26dosearch%3Dtrue%26searchstring%3DHow%252520to%252520reset%252520error%252520code%252520C2204%26useFocusTopic%3Dtrue%26focusTopic%3D9000503&solutionId=20812&isSrch=Yes
12/19/2015 6:49:21 PM •
Canon...
•
Answered
on Dec 19, 2015
Canon ir3570 e000225 0001
During shading operation, the
intensity is below a specific level.
Disconnect and then connect the
flexible cable. Replace the
following as necessary: flexible
cable, CIS, reader controller PCB.
12/2/2015 8:22:29 AM •
Canon...
•
Answered
on Dec 02, 2015
Canon IRC2620 Error Code E000001-0004
This is standard error code for Canon and the fuser unit. The error can be reset by being ready to go into service mode quickly. First press the additional function button, then the 2 & 8 keys at the same time and then the additional function key again. The display should change to the service mode screen, indicating " COPIER " and other accessories. Press " COPIER " then accross the top you should see a menu and select "FUNCTION" then select " CLEAR", then " ERR ", then " OK." This will clear the error from the copiers memory. Turn off the main power switch, wait a few seconds, then turn the copier back on. If you continue to have this error you will have to replace the fixing assembly and if it is similiar to the IRC3220 then you ahve only two screws to remove and the whole unit comes out. You will be saving a service call and I do believe the fuser is over $500. I usually don' tknow the prices of items until I have to do a quote for a customer. Good Luck.
10/2/2015 6:54:01 PM •
Canon...
•
Answered
on Oct 02, 2015
E000748-4041 ERROR CANON IR3100
Dear
The error occurs in accessing to the counter memory PCB.
Disconnect, clean and connect the counter memory PCB,
or replace it.
If problem persists replace the main controller PCB (Main).
Thanks.
2/5/2015 5:27:09 PM •
Canon...
•
Answered
on Feb 05, 2015
Canon c3100 Imagerunner error code E000006-0000
E code Overview
The machine is equipped with a function that checks its state; it runs a check at such times as programmed, and indicates a code on its control panel upon detection of a fault. The tables that follow show codes together with detail codes and the causes associated with the codes and timing of detection. They also offer how these errors may be reset.
press (add func)>(2)>(8)>(add func) on control panel u will see service mode
1)press [copier] > [func] > [error] > [clear]
2) reboot the machine
8/5/2014 3:08:55 PM •
Canon...
•
Answered
on Aug 05, 2014
Not finding what you are looking for?