20 Most Recent
Canon imageRUNNER C3200 Copier - Page 9 Questions & Answers
Error code e000001-0002
Clear the Error code in service mode and power cycle the copierif it does not work you should consider of replacing the fuser
8/29/2012 2:28:49 AM •
Canon...
•
Answered
on Aug 29, 2012
Printer prints with red smudges
Sounds like its a magenta drum going bad. It could also be the transfer cleaning blade assembly, or the transfer belt needing replacement. Do you know if any of these items have been replaced. Drums usually last around 40,000 prints. Transfer belts 300,000 and the blade 100,000. Hope this helps.
8/22/2012 7:23:09 PM •
Canon...
•
Answered
on Aug 22, 2012
Canon e000020-01a0 is it alright to clear the error and work the machine
Yes, The error is a standard code for the drum/developer of a particular color. The 01 is for yellow, the A0 is indicating the measured value of the developer concentration is considerably low. This may be a reult of the drum unit going bad or serveral sensors going bad. How many copies does the yellow drum have on it? Warranty is for approximately 40,000 prints.
8/20/2012 8:36:06 PM •
Canon...
•
Answered
on Aug 20, 2012
Error Code E000001-0004
The main thermistor TH1 has poor contact or open circuit.The thermal switch TP1 has an open circuit.The fixing heater has an open circuit.The SSR is faulty or the DC controller PCB.After the main power switch is turned ON the temperature detected by the main thermistor does not reach 70 C.The error must be reset in service mode :COPIER - FUNCTION - CLEAR - ERR
8/18/2012 10:02:24 AM •
Canon...
•
Answered
on Aug 18, 2012
E000001-0003
The error code is indicating that the fuser thermistors are not detecting a tmeperature in a set amount of time. Try resetting the error code by going into service mode: Press the additional function key, then press the 2 & 8 keys at the same time, then the additional function key again. You should be in service mode. If not press the reset key serveral times to make sure everything is reset and try getting into service mode again. Press the " COPIER " button on the display and the screen changes. Press the " FUNCTION " key across the top of the display and then " CLEAR " then " ERR " and finally " OK ." You have cleared the error out of the copiers memory. Turn off the copier waits a few seconds then power back on. If the error comes back then you have to have the fuser assembly either rebuilt or totally replaced. If you can get a new fuser it can be replaced in a minute by removing the two screws that hold ii in place and putting in the new one a securing it. You will have to reset the error and you may want to do it before replacing the fuser. If it still doesn't work then you may have worse problems that a qualified tech will have to determine. Good Luck.
8/17/2012 8:14:23 PM •
Canon...
•
Answered
on Aug 17, 2012
Why is the print blurry
If black & white copies are ok you can probably bet it is an issue with the ITB (transfer belt assy) or a color registration issue. If black & white copies are also blurry.....could be a variety of issues. If it only happens when you copy but printing is ok from the computer......scanner is at fault.
8/8/2012 12:44:02 PM •
Canon...
•
Answered
on Aug 08, 2012
Clc 3220 paper jam message
Is the display showing a jam in the fixing unit??? Did you l open and close all the doors & covers???? I have found that there is a plastic Exit flag on the small door that folds down on the fixing unit. It is plastic and it can break very easy. You may have to replace the flag. If you have another IR-C3220 try to switch the units with each other copier. The problem could also, be the black connector on the unit or in the copier, it may be broken... It is not easy to change the one inside the copier..... Good Luck
6/6/2012 11:39:02 AM •
Canon...
•
Answered
on Jun 06, 2012
Not finding what you are looking for?