20 Most Recent Behringer Sx2442fx Eurodesk 24channel Mixer New - Page 2 Questions & Answers

0helpful
1answer

Please, I have a Behringer Sx2442fx Eurodesk

yes practically you can use, only make sure you balance the total output frequency
11/13/2011 7:40:58 AM • Behringer... • Answered on Nov 13, 2011
0helpful
1answer

How do you connect behringer sx2442fx eurodesk

WIthout a quality audio interface the answer is you don't... You need to procure an audio interface for the computer. The internal audio systems of computers are too noisy to get decent results. The manual for the mixer will show the typical studio connection with a suggested audio interface.
8/6/2011 4:52:30 PM • Behringer... • Answered on Aug 06, 2011
0helpful
1answer

The cd/tape (standby) button stuck on Behringer

First thing is to get a can of CRC226 from Home depot in the electrical dept. Put a little on a q Tip and work it into the area between the button and the panel. work the button a little bit sideways. Using the point of a scalpel or Xacto knife from one side, gently pry up by sticking the point into the side of the button and levering it up. Once it is up, apply more CRC226 around to lube the button. Be gentle... often contamination gets between the button and the hole in the panel.
7/4/2011 6:07:35 AM • Behringer... • Answered on Jul 04, 2011
0helpful
1answer

How to use a mixer board

Input at each channel XLR or 1/4 ", at faders(bottom) are assignment buttons for sub groups or to stereo out put and main faders drive audio to amps.
2/27/2011 6:15:32 AM • Behringer... • Answered on Feb 27, 2011
0helpful
1answer

Why cant i get the same brilliant sound out of

The mixer should have the same sound quality... the effects MAY be quite different. It is hard to know what you are refering to regarding sound "quality". One must setup the mixer correctly. Critical things are the trim controls and faders. Your faders should be near the unity setting when adjusted. Setting the EQ'a ia important and if you are stereo usage, setting the pan control can be important.
2/25/2011 11:57:13 PM • Behringer... • Answered on Feb 25, 2011
0helpful
1answer

My 4 year old mixer

Sounds like a power supply failure: This will be close to the service manual for your unit:

http://elektrotanya.com/behringer_ub2442fx-pro_sm.pdf/download.html

Check teh power supply output voltages. If no voltage the main switcher has failed. One needs to be adept at electronic repair to repair this and have proper tools and equipment. The switcher runs directely off the input power and work on that portion requires using an isolation transformer for personal safety.
2/25/2011 5:37:25 PM • Behringer... • Answered on Feb 25, 2011
0helpful
1answer

There is a high pitched (approx 4K) sound induced

You neede to do some troubleshooting. Mute the chanels one at a time. Turn certain controls looking for CHANGES to the noise you are getting..There are far too many possibilites to cover here so we need to narrow the possibilities.

First thing: Is the board powered from the same receptacle or power source that your speakers or amps are powered from? If NOT then MAKE IT SO even if it means running an extension cord to power the mixer.
2/19/2011 3:24:47 PM • Behringer... • Answered on Feb 19, 2011
0helpful
1answer

How to install my SL2442FX-PRO ?

1/22/2011 5:35:57 AM • Behringer... • Answered on Jan 22, 2011
0helpful
1answer

I have a Behringer SL2442FX-Pro

First thing to check is the power supply voltages. I have seen a Behringer effect module that had low 5 volts and it continually reset itself.

Schematics: http://elektrotanya.com/behringer_sl2442.pdf/download.html

Typical Behringer mixer should have same DSP as yours and similar or identical power supply

http://elektrotanya.com/behringer_ub1204fx_pro.pdf/download.html
12/30/2010 5:27:16 PM • Behringer... • Answered on Dec 30, 2010
0helpful
1answer

WE ARE EXPERIENCEING RADIO INTERFERENCE AND ARE

I answered a similar question, but want to add that be careful of SUPERSONIC feedback that you can't hear but cooks out your equipment... DO NOT boost highs excessively and watch the levels sent to the speaakers on your indicators... The monitor to mic feedback is very common and if it is above what you can hear, the amps may cook out the speakers, especially the tweeters.
11/30/2010 9:31:29 PM • Behringer... • Answered on Nov 30, 2010
0helpful
1answer

I have a Behringer PMP2000D Europower 800-Watt 14-Channel Powered Mixer & I'm getting no sound out of channels 1-6 but I'm getting a signal just no sound & fuses are fine

You will need an oscilloscope and a good grounding in electronic servicing to attempt a repair. But, check the signal routing. Refer to the user manual.
1/18/2024 7:34:56 AM • Behringer Music • Answered on Jan 18, 2024
0helpful
1answer

I have a Behringer Xenyx 1204FX and the DSP Display doesn't illuminate (but works by pressing down and turning the knob). Any idea why it's not on? Also the AUX 1 Send doesn't seem to be working

It sounds like you're experiencing a couple of issues with your Behringer Xenyx 1204FX mixer. Let's address each of these problems separately:
  1. DSP Display Not Illuminating: The fact that the DSP display works when you press down and turn the knob suggests that the issue might be related to the display itself or its connection. Here are a few steps you can take to troubleshoot the problem:
    • Check Power Source: Ensure that the mixer is receiving proper power and is turned on. Sometimes display issues can be caused by power-related problems.
    • Connection: Make sure the ribbon cable or connector that connects the display to the circuit board is properly seated. A loose connection could be causing the display to not illuminate.
    • Faulty Display: If none of the above steps work, there might be a problem with the display itself. You may need to contact Behringer support or a professional technician to get the display repaired or replaced.
  2. AUX 1 Send Not Working: If the AUX 1 send is not working as expected, there could be several reasons for this:
    • Routing Settings: Make sure that the AUX 1 send is properly routed to the desired destination. Check the routing options on the mixer to ensure that the signal is being sent to the correct output or destination.
    • Level Controls: Verify that the level controls for AUX 1 are set correctly. Make sure that the AUX 1 knob for the specific channel you're working with is turned up.
    • Effects/Processing: If you're trying to send a signal with effects applied, check if the effects are set up correctly. Sometimes, an incorrect effect or routing setting can affect the AUX send.
    • Cable and Connections: Ensure that the cables connecting the AUX 1 send to external devices (such as monitors or effects units) are functioning properly and securely connected.
    • AUX Master Level: Confirm that the AUX 1 master level (usually located on the main output section of the mixer) is turned up to an appropriate level.
If you've gone through these troubleshooting steps and the issues still persist, it might be a good idea to consult the user manual for your Behringer Xenyx 1204FX mixer for further guidance. If the problems continue, you may need to reach out to Behringer support or consider seeking assistance from a professional audio technician or repair service.
8/6/2023 8:22:16 AM • Behringer Music • Answered on Aug 06, 2023
0helpful
2answers

Behringer Europower PMP 1680S--The FX channels both Master and Monitor banks do not create any effects but instead only produce a rapid, repetitive clicking/popping noise. HELP!

Hello Geoff, try using an external processor and check that it works well, if so, the problem is that you have the Jack connectors of Effect sending and those of Return of Effects, dirty Apply a couple of drops of oil, type WD40, to a Plug connector and insert and remove them repeatedly in each connector Jack for sending and returning effects I hope you can solve the problem, comment the results Greetings Franco Dosil Hola Geoff, prueba usando un procesador externo y comprueba que funcione bien, si es asi, el problema es que tienes los conectores Jack de envio de Efecto y los de Retorno de Efectos, sucios Aplicale en un conector Plug un par de gotas de aceite, tipo WD40 y entralos y sacalos repetidamente en cada conector Jack de envio y retorno de efectos Espero puedas solucionar el problema, comenta los resultados Saludos Franco Dosil https://media.music-group.com/media/PLM/data/docs/P0A8M/PMP1680S_PMP980S_PMP960M_M_EN.pdf https://c3.zzounds.com/media/PMP1680S_P0A8M_OI_EN_ES_FR-df44b2314272dfc61a7cabe5bb88ecce.pdf
7/29/2023 2:29:41 AM • Behringer Music • Answered on Jul 29, 2023
0helpful
2answers

Behringer truth 2031a popping and sizziling stoppeed working, what to check first.

Check all the wiring connections on the speaker. Check the plug in points for the cables are not loose in the body of the speaker or the connector plugs themselves are not loose in the actual plug sockets. Next you will need to get inside the speaker body to check the connections and soldered joints. Take a good look at the back of the cable plug sockets and to the back of the actual speaker cone connections. Check each wire at Both ends for damage. No sound at all suggests the issue might be at the 'Input' where the cable plugs into the back of the speaker body.
7/18/2023 3:07:48 PM • Behringer Music • Answered on Jul 18, 2023
0helpful
1answer

Behringer Europower pmp1680s Head/mixer rapidly powers up and down continuously

Sounds like a capacitor is bad.
6/26/2023 1:13:56 AM • Behringer Music • Answered on Jun 26, 2023
0helpful
1answer
Not finding what you are looking for?
Behringer Sx2442fx Eurodesk 24channel Mixer New Logo

40 questions posted

Ask a Question

Usually answered in minutes!

Top Behringer Music Experts

Cindy Wells

Level 3 Expert

6688 Answers

Brad Brown

Level 3 Expert

19187 Answers

john h

Level 3 Expert

29494 Answers

Are you a Behringer Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Behringer Music

  • Behringer Music

Most Popular Question

loose connection sx2442fx

  • Music
Loading...