Top 20
Behringer Sx2442fx Eurodesk 24channel Mixer New Questions & Answers
How to uste focusrite with europower pmp 4000
You will need to give more information for a proper reply, which unit you have and what you want to do with it, what into it and what out etc. In principle you can treat it as a pre/post mixer using it's ins from either the aux or group outs of the mixer or conceivably the inserts depending on what you want to do. You could use it in front of the mixer or as an adjunct. Please tell me what you are trying to do.
2/4/2014 6:44:08 AM •
Behringer...
•
102 views • 0 helpful votes
Jack problems - Main in
First thing is to confirm the leads are fully functional by using a different unit or test the lead with a multimeter set on resistive scale and verify each connection
1/15/2014 2:22:27 PM •
Behringer...
•
117 views • 0 helpful votes
Loose connection sx2442fx
If you don't want to send it back, the next option is to take it apart. If something sounds loose, then it usually is. Maybe you'll be lucky to have a loose cable you can just "plug in." It is quite a complex mixer by the look of it. I was looking for one, but I am unable to find a service manual for it. If I were there I would just take it apart and check for loose connections.
6/16/2012 3:44:30 AM •
Behringer...
•
228 views • 1 helpful votes
My band plugs into the
Either way will work, however your friend's method probably would be slightly better since it goes through less stages within the PMP2000. The "left and right power amp inputs" are the INPUTS to the power amp in the PMP2000 and hence are the best places to connect the mixer if using the PMP2000 as only a power amp. Note doing this will LIKELY disconnect any other input to the PMP2000 from the power amps in it... that is all the preamps in the PMP2000. DO USE TRS cables!!! and power both units from the same receptacle to avoid ground bounce.
8/25/2011 9:16:52 PM •
Behringer...
•
466 views • 1 helpful votes
How do you connect behringer sx2442fx eurodesk
WIthout a quality audio interface the answer is you don't... You need to procure an audio interface for the computer. The internal audio systems of computers are too noisy to get decent results. The manual for the mixer will show the typical studio connection with a suggested audio interface.
8/6/2011 5:14:37 AM •
Behringer...
•
592 views • 0 helpful votes
The cd/tape (standby) button stuck on Behringer
First thing is to get a can of CRC226 from Home depot in the electrical dept. Put a little on a q Tip and work it into the area between the button and the panel. work the button a little bit sideways. Using the point of a scalpel or Xacto knife from one side, gently pry up by sticking the point into the side of the button and levering it up. Once it is up, apply more CRC226 around to lube the button. Be gentle... often contamination gets between the button and the hole in the panel.
7/3/2011 10:59:00 PM •
Behringer...
•
232 views • 1 helpful votes
My 4 year old mixer
Sounds like a power supply failure: This will be close to the service manual for your unit:
http://elektrotanya.com/behringer_ub2442fx-pro_sm.pdf/download.html
Check teh power supply output voltages. If no voltage the main switcher has failed. One needs to be adept at electronic repair to repair this and have proper tools and equipment. The switcher runs directely off the input power and work on that portion requires using an isolation transformer for personal safety.
2/24/2011 7:18:36 PM •
Behringer...
•
229 views • 0 helpful votes
Why cant i get the same brilliant sound out of
The mixer should have the same sound quality... the effects MAY be quite different. It is hard to know what you are refering to regarding sound "quality". One must setup the mixer correctly. Critical things are the trim controls and faders. Your faders should be near the unity setting when adjusted. Setting the EQ'a ia important and if you are stereo usage, setting the pan control can be important.
2/25/2011 8:52:08 PM •
Behringer...
•
202 views • 0 helpful votes
How to use a mixer board
Input at each channel XLR or 1/4 ", at faders(bottom) are assignment buttons for sub groups or to stereo out put and main faders drive audio to amps.
2/27/2011 6:12:38 AM •
Behringer...
•
168 views • 0 helpful votes
There is a high pitched (approx 4K) sound induced
You neede to do some troubleshooting. Mute the chanels one at a time. Turn certain controls looking for CHANGES to the noise you are getting..There are far too many possibilites to cover here so we need to narrow the possibilities.
First thing: Is the board powered from the same receptacle or power source that your speakers or amps are powered from? If NOT then MAKE IT SO even if it means running an extension cord to power the mixer.
2/19/2011 4:12:16 AM •
Behringer...
•
114 views • 0 helpful votes
WE ARE EXPERIENCEING RADIO INTERFERENCE AND ARE
I answered a similar question, but want to add that be careful of SUPERSONIC feedback that you can't hear but cooks out your equipment... DO NOT boost highs excessively and watch the levels sent to the speaakers on your indicators... The monitor to mic feedback is very common and if it is above what you can hear, the amps may cook out the speakers, especially the tweeters.
11/30/2010 4:22:23 PM •
Behringer...
•
92 views • 0 helpful votes
Not finding what you are looking for?