Top 20 ViewSonic N2750w 27 in. HD-Ready LCD Television - Page 2 Questions & Answers

Just to mention that if you have Directv or Dish hooked to the TV, you may need to unplug the satelite receiver for a minute and plug back up. I have seen this happen so many times and people think their TV is at fault. And of course is the possibility of the speakers being cut off in the Sound menu which it looks like you have checked. Lastly, the problem would be in the audio board which Ebay has currently for $18 and shipping $5. Put the model number in the search field at Ebay and scroll down to the audio board.

Hello
Its video decoder has damaged.
there is no repair to bd done to it, as most of its components and SMD [Suface mount Type]; and should be replaced as card. As far as sound is OK, there is no fault ot its video IF or tuner section. Video decoder is combination of digital ICs and extreme care should be taken when replacing this board. You must have through knoledge in digital electronics, and must have a concept of soldering, and have a very good quality digital multimeter to proceed. If you have these, inform me by Fixya, alongwith your email address so that I can send its schematic diagram to you. Viesonic N-2750W and Viewsonic N-2060 models have same circutary and components, except the diamention in screen size. If you are confident that you can do it by yoursel, inform me. I'ss send advice along with schematic diagram.OK.

Look for bad caps in the power supply module first.
http://s807.photobucket.com/albums/yy352/budm/VIEWSONIC/Viewsonic%20N2750W_MARCH%202005/

If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on: Basic troubleshooting guide here: http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm/ Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague Parts: www.shopjimmy.com Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps. Or www.digikey.com just make sure to use caps with low ESR, 105c, high ripple current, long life rating such as PANASONIC FM or FC series.

Bush LCD TV model ?

Yes there is... You are going to need a VGA cable and an 1/8 audio cable (for sound)

http://support.dell.com/support/edocs/systems/ins1520/en/om_en/pdf/UX8623D.pdf - On page 29 it shows a picture of the right side of your computer. You will hook the VGA cable to the VGA port (Number 8 on the diagram).
The on your tv you will hook it up to the vga port as well. Page 7 of the following document shows a pictures of the back of your tv. You will hook it up to "L" on the diagram. Be careful to not bend the pins in the connector. http://www.viewsonic.com.au/support/manuals/files/LCd%20TV/N2750w%20User%20Guide%20English.pdf
Switch your tv over to the PC input by clicking the "Input" button. Then make sure your PC is sending a signal, you might have to hit the function key to switch the view.

Most likely a small surface mount fuse near the inlet of the 24v rail needed to light the tv with the backlight inverter. You may also have a CCFL bulb that is going out. If they run in a series then one bulb that is old and burning out will power down the rest of the bulbs (I ran into this problem with a 42" samsung once and that fixed it)


Thank you

HOPE this helps :)

The closed captioning (for whatever reason) may be hidden under "Parental Controls"section of the
menu.
I'm reading between the lines (no online user manual available) from:
http://www.newegg.com/Product/Product.aspx?Item=N82E16889107001

Hi,

You could order a substitute remote ( as original is not available any longer ) from :-

http://remotes.com/store/viewsonic/n2750w.html

If you want to buy universal remote, be advised that for Viewsonic it would not be too successful and moreover, the one which is compatible ( Harmony ) would be expensive.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Which means you are not getting any video, I am guessing you have tried all inputs like video 1,2,3 etc and tuner air or cable. If you have then it's your video board.

This is the instruction for my N2750/3250 remote.
Resetting Remote
• To reset remote and access default settings press and hold desire device button for roughly six seconds and enter three digit reset code 000.

• Replace batteries if remote control keys are not functioning properly, this is a normal behavior that indicates batteries are low.

N2750 IS 008

N1700W
001
N1300
002
N1500
003
N1750W
004
N2010
005
N2010-E
006
N2700W
007
N2750W
008
N3020W
009
N3200W
010
N3200W-E
011
VPW4255
012
VPW5500
012
N2000
014
N3000W
015


Email me if you want me to send you the full PDF from VIEWSONIC, [email protected]

I had a similar problem with my 42 in Philips LCD HDTV. Here was the problem. My Power Supply Board had several bad capacitors. I opened my TV (warranty was expired ofcourse) and found four bulged capacitors on the PSB. Many major electronics companiesPhilips/Magnavox, Sony, Panasonic, and others were sold capacitors that failedin 2-5 years instead of 10-20. Thecapacitors fail prematurely due to a lack of preservatives. Unfortunately, they were installed in allsorts of devices and cause a wide range of failure problems. Here are some options for you. 1. Have it fixed by a professional $$$$$$$??????? (Is itunder warranty?) Remember, TVs CONTAINHIGH VOLTAGE AND CAN KILL YOU! Do this at your own risk. 2. Open your TV and find PSB. (The board that the power cordplugs into) Check for faulty caps. If you find some (bulged or leaking) bad capsreplace the entire board. The entireboard costs around $250 right now because they are in high demand right now.They can be found at tv-part.com but supplies are limited. I would definitely shop around though. 3. Remove and then replace individual faulty caps. This takes some soldering skill. Caps are inexpensive and if you can take care of it yourselfit will save you hundreds. This may be your problem. If you determine that it might be. I have a Tip/How TO tutorialon this site that may also help. Itgives step by step instructions for replacing caps on PSB #715t2432-2. If this isyour board you are in luck. Here is theLink: Fixingthe Philips Turns/shuts off on its own problem. I'm working on uploading pictures to helpguide people though the process as well. Let me know if I can do anything to help. Hope this helps and if it does please rate itaccordingly. Good luck.Kaufman605

check your speaker cable, may be your speaker cable didnt connect properly

It can be due to bad caps in the power supply (24vdc) or failing backlight inverter boards. You need to check the power supply caps and the DC voltages first.
http://s807.photobucket.com/albums/yy352/budm/Viewsonic%20N2750W_MARCH%202005/

If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on: Please see my basic troubleshooting guide here: http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide Failed TV and Monitors: http://s807.photobucket.com/home/budm/allalbums http://en.wikipedia.org/wiki/Capacitor_plague Parts: www.shopjimmy.com Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps. Please post back what you find.

Tries unplug,replug the tv it back like about an hour later.Now ur tv is resetting back to it factory setting.Ur tv should have correct colors now.Not,than ur tv could have missing the red color.Try the tv with another incomming broadcasting signal cable in a diffrent location,see if u have good and all of it tv colors.Yes,than that location incomming broadcasting signal cable is bad.Not than the tv Tuner signal board is bad.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish Tuner signal board for the replacement.

You may want to inspect the power supply first to make sure it does not have any bad caps and correct voltages. Please see my pictures here: http://s807.photobucket.com/albums/yy352/budm/Viewsonic%20N2750W_MARCH%202005/

If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on: Please see my basic troubleshooting guide here: http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting Failed TV and Monitors: http://s807.photobucket.com/home/budm/allalbums Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague Parts: www.shopjimmy.com Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps.

try using the number keys on control an manually program numbers in that way, if you select auto tune, it will only try to program any channel it gets signal for, once you type the numbers in that way, it should ask you to save that channel number, in which of course you select yes... try that, also refer to owner manual or mfg website.

It can be the power supply or inverter board, main board problem, need troubleshooting first, common problems are power supply and inverter board.
http://s807.photobucket.com/albums/yy352/budm/Viewsonic%20N2750W_MARCH%202005/

If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on: Please see my basic troubleshooting guide here: http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide Failed TV and Monitors: http://s807.photobucket.com/home/budm/allalbums http://en.wikipedia.org/wiki/Capacitor_plague Parts: www.shopjimmy.com Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps.

You can use a set of component cable (RED/BLUE/GREEN with RCA plugs) and the RED/WHITE RCA plugs for the audio. Does the CABLE BOX have those outputs or it has HDMI.

Basic LCD monitor and LCD TV troubleshooting guide:

http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting

http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide

Failed TV, Monitors, Caps : http://s807.photobucket.com/home/budm/allalbums Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

This is caused by the failure of a filtering capacitor in the audio amplifier section of the tv. Just open the back of the tv, locate the failed part (some testing will be necessary) unsolder it, buy an identical replacement and solder it back on the board.

Check DC filter caps in the power supply first:
http://s807.photobucket.com/albums/yy352/budm/Viewsonic%20N2750W_MARCH%202005/

If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on: Please see my basic troubleshooting guide here: http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide Failed TV and Monitors: http://s807.photobucket.com/home/budm/allalbums http://en.wikipedia.org/wiki/Capacitor_plague Parts: www.shopjimmy.com Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps.