ViewSonic N2750w 27 in. HD-Ready LCD Television - Page 8 - Answered Questions & Fixed issues
Please scan channels
try hitting the input button or go to channel 3. the sat box can only output to channel 3 or 4 or if using Dish network try channel 66 or what ever the channel it outputs. it also can output via video cables so check each video setting on the set. make sure the box is on first.
Pasansonic viera
scart and S Vid are to differant worlds S-Vid carries Y and Croma signals (y Is lumans and croma is color) and is in NTSC only.
TV just turns itself off
does this happen at night or dark days when lights are on? if so you might be using CFL lights which interer with IR info to the set. it can cause other problems such as random cannel change or no remote responce.
Black line in my Sharp TV
yes 100% is ur lcd panel fail-- what u can do open the unit follow the lcd panel video cable,from the videoboard to the lcd panel input,,take ur time remove ,it shouln"t be to hard to removed,,after stand up the unit clear around it, the turn it on,if u see the line still there,that means ur lcd panel is finish it should be replace , if no line it could be ur cable faulty,,trust me i"m a service tech for 12years,& i still do ,thatks good luck
Remote controle code
There are some codes for Viewsonic tv's but apparently it's really hard to program and the codes even change. I read somewhere once that the best way to program it is to try with those really expensive remotes that can program everything, but you will need to contact viewsonic for the software to upload to that remote.
V-Chip
Typically the dafault password is either:
0000
1234
9999
Let us know :-)
Pc hook-up/sound issues
on the bottom of the monitor there is a audio input. you must connect you pc output(green) to the monitor input with a male to male audio cord.
you can also use a rca cord with two adapters.
Greenish tint
First of all component inputs are analog as the only digital inputs are the DVI or HDMI inputs on a TV. You might have color adjutments in the menus somewhere that allow you to compensate for color weakness on one or more colors. If not you most likely have a bad digital board.
Why is my vizio tv's picture black and white?
it could be your flux capacitor is out. you might need to plug it in goto menus and check to see if ur runnin 21 gigawatts if not leave it plugged in and off for two days and it should refresh it
12/29/2022 9:16:23 AM •
ViewSonic...
•
Answered
on Dec 29, 2022
•
27,123 views
Tune my viewsonic n3246w tv
First make sure that the current input Source is set to TV to see the option for scanning for channels. There is a Source button on the front of the TV. (It's on the right side as you look at the front of the TV.) The Source button on the original remote is on the left side below the number keys.There are two RF (coaxial) cable inputs near the VGA port on the back of the TV. The digital RF signal needs to go to the port above the VGA port.
To scan for analog channels, press the Menu button. Then navigate to the TV setup option with the Up/Down arrows. Press OK to enter the menu. You can use either the Auto search or the Manual search. However, the Auto will be faster. You can set your country or leave it to Auto. Navigate to Start and press OK for the Auto-scan. There is a DTV menu button above the Volume + button on the remote. Use this menu and look for the Installation section to scan for channels. Again there is an Auto or Manual option.
ManualsLib has the manual for the Viewsonic N3246W here:
https://www.manualslib.com/manual/306714/Viewsonic-N3246w.html. See page 23 for the start of the analog TV channel scan information. See page 30 for the digital TV scan.
I hope this helps.
Cindy Wells
(For any channel provided by a set-top box, you will not be able to use the TV to store the channel lists.)
4/25/2019 6:17:35 PM •
ViewSonic...
•
Answered
on Apr 25, 2019
•
282 views
Not finding what you are looking for?