20 Most Recent
Dyson AM08 Pedestal Fan - Page 8 Questions & Answers
BULB REPLACEMENT
I found the articles on
Harbor Breeze helpful for solving remote control problems. You can also check out the video below as well.
I found the articles on
Harbor Breeze Accessories helpful for solving remote control problems. You can also check out the video below as well.
7/21/2023 9:56:56 AM •
Dryers
•
Answered
on Jul 21, 2023
Concord fan lights work, fan only at low speed.
Based on the information provided, it is possible that the issue lies with the Zing Ear ZE-208D 3 speed switch. This switch controls the fan speed and if it is not functioning properly, it could cause the fan to only run at the lowest speed. It is also possible that there could be an issue with the transformer or another component, but without further testing it is difficult to determine the exact cause of the problem.
One potential solution would be to replace the Zing Ear ZE-208D 3 speed switch. This can be done by disconnecting the wires from the old switch and connecting them to the new switch in the same configuration. It is important to ensure that the new switch is compatible with the fan and has the same number of wires as the old switch.
Another potential solution would be to check the wiring connections between the switch and the fan motor. Loose or damaged connections could cause issues with the fan speed.
If neither of these solutions work, it may be necessary to consult a professional electrician or contact Concord for further assistance.
6/21/2023 7:53:48 PM •
Dryers
•
Answered
on Jun 21, 2023
Bush td7cnbcw tumble dryer, always worked perfectly. Only trying to turn it on the morning and the 3 and 9 hrs lights started flashing after 3 turns. Anyone know what this means?
The flashing lights on your Bush TD7CNBCW tumble dryer could indicate an error or fault in the machine. While I don't have access to specific error codes for this particular model, I can provide some general troubleshooting steps that may help you identify and resolve the issue:
1. Check the user manual: Refer to the user manual that came with your tumble dryer. It should contain information about error codes and their meanings. Look for any reference to the flashing lights you are seeing.
2. Power cycle the dryer: Turn off the dryer and unplug it from the power source. Wait for a few minutes, then plug it back in and try turning it on again. Sometimes, power cycling can help reset the machine and clear minor glitches.
3. Check the door switch: Ensure that the door of the tumble dryer is fully closed and latched. The machine may not start if the door switch is not engaged properly.
4. Clear any obstructions: Make sure the drum inside the dryer can spin freely and is not obstructed by any items or lint buildup. Clear out any debris or lint that may be blocking the drum or the lint filter.
5. Check the water tank and filter: If your tumble dryer has a water tank or condenser unit, ensure that it is empty and clean. Additionally, clean the lint filter to ensure it is not clogged, as this can affect the dryer's performance.
6. Consult customer support: If the issue persists and you cannot find a resolution in the user manual, it is recommended to contact the Bush customer support or a qualified technician who can provide specific guidance and assistance for your model.
Remember, safety should always be a priority when dealing with electrical appliances. If you're unsure or uncomfortable with troubleshooting the issue yourself, it's best to seek professional help to avoid any risks or further damage to the appliance.
6/21/2023 2:44:44 AM •
Dryers
•
Answered
on Jun 21, 2023
How do I change belt on Model LD7600 dryer
To change the belt on your Model LD7600 dryer, follow these general steps for a safe and effective replacement:
1. Start by disconnecting the dryer from the power source to ensure your safety.
2. Access the dryer drum by removing either the top panel or front panel, depending on the design of your Model LD7600. Check your user manual or specific instructions for the correct method.
3. Remove the old belt by carefully releasing its tension and taking note of how it is routed around the pulleys. Then, remove it from the pulleys.
4. Install the new belt by looping it around the drum and ensuring it's positioned in the groove. Refer to diagrams or your user manual to ensure proper routing.
5. Check the belt tension. Adjust the tensioning mechanism as needed to ensure the belt is not too tight or too loose.
6. Reassemble the dryer by replacing the top or front panel and securely fastening all screws or clips.
7. Test the dryer by plugging it back in and running a dry cycle to ensure proper functioning.
Keep in mind that specific models may have slight variations in the replacement process. Always refer to your user manual or manufacturer's instructions for accurate guidance.
6/6/2023 9:50:21 PM •
Dryers
•
Answered
on Jun 06, 2023
Harbor breeze LGF-1
great question. The good thing is that in order to remove ceiling fan blades from a ceiling fan, the instructions are generally straight forward and generic. In most cases, you'll need to shut the power off at the breaker or the fuse panel and then use a Phillips screw driver head to remove the blades.
Here's an article that provides a good step by step on how to accomplish this task:
https://hampton-lighting.com/how-to-remove-ceiling-fan-blades/
5/14/2023 1:39:47 PM •
Dryers
•
Answered
on May 14, 2023
Not finding what you are looking for?